The recycling of cellulose from cotton textiles would minimize the use of virgin crop fibers, but recycled polymers are generally inferior in mechanical performance to those made from virgin resins. This challenge prompted the investigation of biobased additives that were capable of improving the mechanical properties of fibers by means of antiplasticizing additives. In this study, regenerated cellulose (RC) fibers were spun from cellulose found in cotton T-shirts, and fibers were mechanically strengthened with glucaric acid (GA), a nontoxic product of fermentation. The recycled pulp was activated using aqueous sodium hydroxide and then followed by acid neutralization, prior to the direct dissolution in lithium chloride/N,N-dimethylacetamide (LiCl/DMAc) at 3 wt.% cellulose. At 10% (w/w) GA, the tensile modulus and strength of regenerated cellulose from recycled cotton fibers increased five-fold in contrast to neat fibers without GA. The highest modulus and tenacity values of 664 cN/dtex and of 9.7 cN/dtex were reported for RC fibers containing GA.
12 August 2024 in Journal of Materials Chemistry B
Mosquito-borne diseases are responsible for 700 000 deaths annually. Current outdoor protective strategies primarily focus on direct skin application of commercial repellents (i.e., aerosol sprays or topical lotions) which are typically limited to efficacy times of ≤10 hours due to rapid evaporation and dermal absorption. Consequently, frequent reapplication for continuous protection can increase associated health hazards and cause noncompliance. This study utilizes Hansen solubility parameter modeling to design physical gels composed of insect-repelling N,N-diethyl-meta-toluamide (DEET) and modacrylic copolymer poly(acrylonitrile-co-vinyl chloride) (P(AN–VC)). The P(AN–VC)/DEET composites exhibit tunable and reversible sol–gel transition temperatures that can meet the thermomechanical stability demands of the intended application and permit facile transition to commercial melt processing techniques such as injection molding, filament spinning, or film casting. P(AN–VC)/DEET gel films demonstrate mosquito repellency for more than half a year—performing longer than any other known material to date—due to the high reservoir of repellent and its desorption hindrance from the polymer matrix. Therefore, P(AN–VC)/DEET gels hold significant potential for extended protection against mosquitos and other biting arthropods.
Personal protection from mosquitos is dominated by topically applied aerosol sprays or lotions, which demonstrate efficacy durations of no longer than 10 h, thus encouraging the research and development of long-term insect-repelling devices. Repellent-loaded polymeric matrices have driven the development of insect-repelling apparel fabrics; however, most efforts either fail to offer the tensile properties demanded from apparel applications or only demonstrate repellency durations for multiple days. This study utilizes poly-D,L-lactic acid (PDLLA) as a compatibilizer between Nylon 12 and nootkatone for enhanced nootkatone retention throughout fabric manufacturing processes. Nootkatone-infused Nylon 12/PDLLA composites demonstrate up to a 14% increase in nootkatone retention throughout fabric manufacturing compared to pure Nylon 12, underscoring the importance of polymer/substrate miscibility on substrate retention. Moreover, while nootkatone-infused Nylon 12 filaments demonstrate decreasing tensile stress at breaks with increasing nootkatone content, Nylon 12/PDLLA filaments exhibit similar tensile properties regardless of nootkatone content. The PDLLA domains are suspected to behave as reservoirs for excess nootkatone to prevent its role as a defect within the Nylon 12 matrix. The resulting knits exhibit significant mosquito repellencies over 24 h dependent on the nootkatone concentration, thus demonstrating potential to embed insect repellent within high-performance polymeric filaments with effective mosquito repellencies. Therefore, the incorporation of PDLLA as a compatibilizer holds significant potential for enhanced nootkatone retention during Nylon 12 fabric manufacturing.