The relationship between point defects and mechanical properties has not been fully understood yet from a theoretical perspective. This study systematically investigated how the Stone–Wales (SW) defect, the single vacancy (SV), and the double vacancy (DV) affect the mechanical properties of graphene/aluminum composites. The interfacial bonding energies containing the SW and DV defects were about twice that of the pristine graphene. Surprisingly, the interfacial bonding energy of the composites with single vacancy was almost four times that of without defect in graphene. These results indicate that point defects enhance the interfacial bonding strength significantly and thus improve the mechanical properties of graphene/aluminum composites, especially the SV defect. The differential charge density elucidates that the formation of strong Al–C covalent bonds at the defects is the most fundamental reason for improving the mechanical properties of graphene/aluminum composites. The theoretical research results show the defective graphene as the reinforcing phase is more promising to be used in the metal matrix composites, which will provide a novel design guideline for graphene reinforced metal matrix composites. Furthermore, the sp3-hybridized C dangling bonds increase the chemical activity of the SV graphene, making it possible for the SV graphene/aluminum composites to be used in the catalysis field.
Buckled tetragonal graphene (BTG), a novel allotrope of graphene, has been reported to possess Dirac-like fermions and high Fermi velocities. However, the stability of BTG is still controversial. Here, first principles calculations and ab initio molecular dynamics (AIMD) were performed to study the stability of three kinds of tetragonal graphenes (TGs), including planar tetragonal graphene (PTG), BTG reported by Liu et al. [Phys. Rev. Lett., 2012, 108, 225505] and the novel BTG constructed by us. For the two BTGs, phonon dispersions predict that they are stable, but this conclusion is contradictory with the results of energy analysis, vibrational mode analysis and AIMD simulations. Our electronic structure analysis shows that the delocalized Π bonds formed by unbonded pz electrons drive the stability of PTG and may induce the transformation of the two BTGs into PTG. Our further study of phonon dispersions on planar hexagonal graphene (PHG) and buckled hexagonal graphene (BHG) indicates that the phonon dispersion at 0 K may have some limitations in predicting the stability of 2D carbon materials and thus cannot accurately describe the stability of BTGs. In addition, we have predicted several hydrogenated and fluorinated TGs, and theoretically demonstrated that chemical modification can make metallic PTG become a semiconductor with a certain bandgap. Moreover, the bandgaps of these new materials can be further regulated by increasing the thickness of the carbon atomic layer, which makes them promising for semiconductor devices and energy storage.
A series of adsorption configurations with less than 2% lattice mismatch of graphyne adsorbed at different sites on the (111) surface of Cu, Ag and Au are obtained by a systematic rotation of the graphyne sheet. Besides, all the non-equivalent adsorption configurations of graphyne on metal surfaces are obtained by a structure screening method based on the translation of graphyne sheet and the calculation of the atomic overlapping area at the interface. The most stable adsorption configuration of graphyne on each metal surface is obtained by optimizing these non-equivalent adsorption configurations with a small computational cost. Then the adsorption energy, differential charge density, and partial density of states are calculated using a first-principles method in order to investigate the bonding mechanism between graphyne and the (111) surface of these three metals. The results show that the adsorption types of graphyne on the (111) surface of Cu, Ag and Au are chemisorption, chemical and physical mixed adsorption and pure physisorption, respectively. In detail, when a metal (Cu or Ag) atom is below a C atom, the C-pz orbital will interact with the s and d orbitals of the metal atom and then form a covalent bond with the metal atom. In particular, when a Cu atom lies below two carbon atoms joined by an acetylene bond, the s and d orbitals of the Cu atom hybridize with each other to form two identical sd orbitals and then form two covalent bonds with two C-pz orbitals. Our results not only provide a structure screening method for obtaining the most stable configuration with a very small lattice mismatch but also reveal the interface bonding mechanism between graphyne and metals, which will provide help for the preparation of graphyne and its application in composite materials.