In this work, we prepared nonionic surfactants from waste cooking oil materials. Hydrolysis was carried out for palm and palm kernel waste cooking oils to get a mixture of free fatty acids. The mixture of free acids was esterified with sorbitan and then ethoxylated at different ethylene oxide units. Two surfactants exhibited promising surface-active properties among the six prepared surfactants based on the results of surface tension. The interfacial tension (IFT) around the critical micelle concentration was measured against a series of n-hydrocarbon to detect the minimum alkane carbon number (ACN) (Πmin) for each of these surfactants. The effect of normal and branched alcohols on Πmin was also studied to design the surfactant/alcohol mixture for the chemical flooding process. From the results of IFT, the ethoxylated ester derivatives of palm kernel fatty acids (EPK-20) exhibited minimum IFT γmin (0.06 mN m–1) at Πmin equal to 12, and the ethoxylated ester derivatives of palm fatty acids (EP-40) achieved γmin equal to 0.09 mN m–1 at Πmin of 10. Branched alcohols shifted Πmin to a higher value to reach the equivalent ACN of the crude oil and decrease the IFT to lower values. The flooding process showed that the maximum oil recovery was obtained by EPK-20 (54.2% when used purely and 66.2% when used with isoamyl alcohol). In comparison, EP-40 exhibited that oil recovery equals 46% without alcohol and 46.4% with iso-butanol alcohol. The results were interpreted and discussed based on interfacial properties, wettability alteration, and the ACN.
Esters were found to be promising alternatives to oil, as a constituent of drilling fluids, due to their biodegradability and bioaccumulation attributes. In this study, we used ethyl octanoate ester (EO) as a low molecular weight synthetic oil for formulating an ester-based drilling fluid (EBDF). Aluminum oxide nanorods (nanoparticles) were introduced as a Pickering emulsion stabilizer. Like the commercial emulsifiers, they showed that they stabilized the invert emulsion drilling fluid in our study. The rheological and filtration properties of the EBDF were tested at normal pressure and three temperatures: low temperature deepwater (LT) conditions of 2.6 °C, normal pressure and normal temperature (NPNT) conditions of 26.8 °C, and elevated temperature conditions of 70 °C. To enhance the stability and filtration properties of the drilling fluid, aluminum oxide nanoparticles (NPs) were used. An optimum concentration of 1 wt% was found to provide superior rheological performance and higher stability than samples without NPs at NPNT, LT, and elevated temperature conditions. Steadier gel rheology was exhibited at elevated temperature conditions, and a slow rate of an increasing trend occurred at the lower temperatures, with increasing NP concentrations up to 1.5 wt%. Filtration loss tests presented a reduction of fluid loss with increasing the NP concentration. The results demonstrate that a reduction of up to 45% was achieved with the addition of 1 wt% NP. These results show that nano-enhancement of ethyl octanoate drilling fluids would suffice to provide a wider range of operational temperatures for deepwater drilling operations by providing better thermal stability at elevated temperatures and maintaining stability at lower temperatures.
28 June 2024 in Journal of Petroleum and Mining Engineering
Inadequate wellbore cleaning is a recurring problem as removing cuttings from thousands of meters from the downhole to the surface is challenging during any drilling process. High concentrations of cuttings or any drilling fluid residues left at the bottom or challenging sections of the well could cause formation damage, impede well completion, and damage completion tools. To avoid expensive workover services such as fishing and clean-up procedures, this work comprehensively reviews past studies related to hole cleaning. Therefore, we aim to systematically provide data on recent hole-cleaning flow loop designs, and discuss the main findings of studies based on important factors affecting hole cleaning and simulation modeling. Interrelated impacts of rheological properties of drilling fluids, flow rate, hole inclination, hole eccentricity, drill pipe rotation, and cutting size in hole cleaning processes are discussed. Furthermore, this study presents an overview of various analytical and numerical modeling approaches that are used for hole-cleaning analyses. Also, the role of artificial intelligence (AI) and machine learning (ML) in predicting the hole cleaning process, was discussed. Finally, the challenges that currently exist in the hole-cleaning process are highlighted to provide insights for further investigations in this area.