This study proposes an analysis of the physics-based TCAD (Technology Computer-Aided Design) simulation procedure for GaN/AlGaN/GaN HEMT (High Electron Mobility Transistor) device structures grown on Si (111) substrate which is calibrated against measurement data. The presence of traps and activation energies in the device structure will impact the performance of a device, the source of traps and position of traps in the device remains as a complex exercise until today. The key parameters for the precise tuning of threshold voltage (Vth) in GaN transistors are the control of the positive fixed charges −5 × 1012 cm−2, donor-like traps −3 × 1013 cm−2 at the nitride/GaN interfaces, the energy of the donor-like traps 1.42 eV below the conduction band and the acceptor traps activation energy in the AlGaN layer and buffer regions with 0.59 eV below the conduction band. Hence in this paper, the sensitivity of the trap mechanisms in GaN/AlGaN/GaN HEMT transistors, understanding the absolute vertical electric field distribution, electron density and the physical characteristics of the device has been investigated and the results are in good agreement with GaN experimental data.
In this study, the onset amplitude of the initial capillary surface wave for ultrasonic atomization of fluids has been implemented. The design and characterization of 485 kHz microfabricated silicon-based ultrasonic nozzles are presented for the concept of economic energy development. Each nozzle is composed of a silicon resonator and a piezoelectric drive section consisting of three Fourier horns. The required minimum energy to atomize liquid droplets is verified by COMSOL Multiphysics simulation software to clarify experimental data. The simulation study reports a minimum vibrational amplitude (onset) of 0.365 μm at the device bottom under the designated frequency of 485 kHz. The experimental study agrees well with the suggested frequency and the amplitude concerning the corresponding surface vibrational velocity in simulation. While operating, the deionized water was initially atomized into microdroplets at the given electrode voltage of 5.96 V. Microdroplets are steadily and continuously formed after the liquid feeding rate is optimized. This newly designed ultrasonic atomizer facilitates the development of capillary surface wave resonance at a designated frequency. A required vibrational amplitude and finite electric driving voltage promote not only the modern development in the green energy industry, but also the exploration of noninvasive, microencapsulated drug delivery and local spray needs.
The novel drug delivery system refers to the formulations and technologies for transporting a pharmaceutical compound in the body as it is needed to safely achieve its desired therapeutic effects. In this study, the onset vibrational amplitude of capillary surface waves for ultrasonic atomization spray is explained based on Faraday instability. Using ultrasonic frequency, the vibrational amplitude approached a critical point, and the liquid surface broke up into tiny drops. The micro-droplets were are steadily and continuously formed after the liquid feeding rate was optimized. The simulation study reported a minimum vibrational amplitude or onset value of 0.38 μm at 500 kHz frequency. The required minimum energy to atomize the drops was simulated by COMSOL Multiphysics simulation software. The simulation result agreed well with the numerical results of a subharmonic vibrational model that ocurred at 250 kHz frequency on the liquid surface. This newly designed single frequency ultrasonic atomizer showed its true physical characteristic of resonance on the fluid surface plane. Hence, this research will contribute to the future development of a single-frequency ultrasonic nebulizer and mechatronics for the generation of uniform atomized droplets.
The extremely low-frequency (ELF) and its corresponding electromagnetic field influences the yield of CMOS processes in the foundry, especially for high-end equipment such as scanning electron microscopy (SEM) systems, transmission electron microscopy (TEM) systems, focused ion beam (FIB) systems, and electron beam lithography (E-Beam) systems. There are several techniques to mitigate electromagnetic interference (EMI), among which active shielding systems and passive shielding methods are widely used. An active shielding system is used to generate an internal electromagnetic field to reduce the detected external electromagnetic field in electric coils with the help of the current. Although the active shielding system reduces the EMI impact, it induces an internal electromagnetic field that could affect the function of nearby tools and/or high-performance probes. Therefore, in this study, we have used a C-shaped cylindrical device combined with an active shielding system and passive shielding techniques to reduce EMI for online monitoring and to overcome the aforementioned issues. In this study, the active shielding system was wrapped with a permalloy composite material (i.e., a composite of nickel and iron alloy) as a tubular device. A C-shaped opening was made on the tubular structure vertically or horizontally to guide the propagation of the electromagnetic field. This C-shaped cylindrical device further reduced electromagnetic noise up to −5.06 dB and redirected the electromagnetic field toward the opening direction on the cylindrical device. The results demonstrated a practical reduction of the electromagnetic field.
There are many high-power electrical cables around and within semiconductor foundries. These cables are the source of extremely low-frequency (ELF < 300 Hz) magnetic fields that affect the tools which operate by the function of electronic beams. Miss operation (MO) happens because the ELF magnetic fields induce beam shift during the measurement or process for cutting-edge chips below 40 nm. We present the optimal permutation of power transmission lines to reduce electromagnetic influence in high-technology nano fabs. In this study, the magnetic field was reduced using a mirror array power cable system, and simulation results predicted the best permutations to decrease the electromagnetic interference (EMI) value to below 0.4 mG in a working space without any shielding. Furthermore, this innovative method will lower the cost of high-technology nano fabs, especially for the 28 nm process. The motivation behind this paper is to find the ideal permutation of power transmission lines with a three-phase, four-cable framework to decrease the EMI in high-technology nano fabs. In this study, the electromagnetic interference was diminished using the ideal-permutation methodology without investing or using additional energy, labor, or apparatus. Moreover, this advanced methodology will help increase the effectiveness and reduce the costs of nano fabs. The mathematical and experimental results of the study are presented with analysis.
10 October 2025 in Semiconductor Science and Technology
This work presents a detailed Technology Computer Aided Design (TCAD) and Transport of Ions in Matter (TRIM)-based simulation study of normally off AlGaN/GaN high-electron-mobility transistors (HEMTs), focusing on the influence of the thickness of the GaN cap layer on device performance. The study evaluates threshold voltage modulation through nitrogen ion implantation across cap thicknesses of 0 , 1 , and 2 nm. The 2 nm cap configuration yielded optimal results, including a breakdown voltage of 720 V, a drain current density of 1.45 × 10−2 A mm−1, a gate leakage current of 5.35 × 10−11 A mm−1, and a positive threshold voltage of 0.366 V. TRIM simulations confirmed that the cap layer significantly affects nitrogen ion distribution and damage profiles, influencing two-dimensional electron gas formation. Schottky barrier height variations were also observed, correlating with cap-induced modulation of the surface potential. Although converter-level efficiency is influenced by passives, parasitics, and control strategies, our device-level results indicate that cap-optimized HEMTs can enable high-efficiency operation in MHz-class buck converters. These findings underscore the effectiveness of GaN cap-layer engineering in strengthening the breakdown, improving the gate control, and enhancing overall enhancement-mode GaN HEMT performance.