NASA’s Double Asteroid Redirection Test (DART) mission is the first full-scale test of the kinetic impactor method for asteroid deflection, in which a spacecraft intentionally impacts an asteroid to change its trajectory. DART represents an important first step for planetary defense technology demonstration, providing a realistic assessment of the effectiveness of the kinetic impact approach on a near-Earth asteroid. The momentum imparted to the asteroid is transferred from the impacting spacecraft and enhanced by the momentum of material ejected from the impact site. However, the magnitude of the ejecta contribution is dependent on the material properties of the target. These properties, such as strength and shear modulus, are unknown for the DART target asteroid, Dimorphos, as well as most asteroids since such properties are difficult to characterize remotely. This study examines how hydrocode simulations can be used to estimate material properties from information available post-impact, specifically the asteroid size and shape, the velocity and properties of the impacting spacecraft, and the final velocity change imparted to the asteroid. Across >300 three-dimensional simulations varying seven material parameters describing the asteroid, we found many combinations of properties could reproduce a particular asteroid velocity. Additional observations, such as asteroid mass or crater size, are required to further constrain properties like asteroid strength or outcomes like the momentum enhancement provided by impact ejecta. Our results demonstrate the vital importance of having as much knowledge as possible prior to an impact mission, with key material parameters being the asteroid’s mass, porosity, strength, and elastic properties.
On 2022 September 26, the Double Asteroid Redirection Test (DART) spacecraft intentionally collided with Dimorphos, the moon of the binary asteroid system 65803 Didymos. This collision provided the first full-scale test of a kinetic impactor for planetary defense. Images from DART’s DRACO camera revealed Dimorphos to be an oblate spheroid covered in boulders of varying sizes and shapes. Very little was known about Dimorphos prior to DART’s impact, including its shape, structure, and material properties. Approach observations and those following the DART impact have provided crucial knowledge that narrows the parameter space relevant to modeling the impact into Dimorphos. Here we present the results of a suite of hydrocode simulations of the DART impact on Dimorphos. Despite remaining uncertainties, initial models of DART’s kinetic impact provide important information about the results of DART (e.g., potential crater size and morphology, ejecta mass) and the properties of Dimorphos. Simulations here suggest that Dimorphos has near-surface strength ranging from a few Pascals to tens of kPa, which corresponds to crater sizes of ∼40–60 m. Simulated crater sizes provide a crucial comparison metric for the European Space Agency Hera mission when it arrives at the Didymos system. Hera’s measurement of crater size in combination with measurement of Dimorphos’s mass will allow us to assess our simulations and provide the information needed to make the DART impact experiment both the first test of a planetary defense mitigation mission and the first full-scale planetary defense simulation validation exercise.
Large scale computational models are important for studying impact cratering events that are prevalent both on Earth and, more broadly, in this solar system. To address these problems, models must reliably account for both large length scales (e.g., kilometers) and relatively long time scales (hundreds of seconds). This work benchmarks two such approaches, a more traditional hydrodynamics approach and a finite-discrete element method (FDEM), for impact cratering applications. Both 2D and 3D results are discussed for two different impact velocities, 5 km/s and 20 km/s, striking normal to the target and, for 3D simulations, 45° from vertical. In addition, comparisons to previously published data are presented. Finally, differences in how these methods model damage are discussed. Ultimately, both approaches show successful modeling of several different impact scenarios.
1 September 2018 in Journal of Verification, Validation and Uncertainty Quantification
Verification and validation (V&V) are necessary processes to ensure accuracy of the computational methods used to solve problems key to vast numbers of applications and industries. Simulations are essential for addressing impact cratering problems, because these problems often exceed experimental capabilities. Here, we show that the free Lagrange (FLAG) hydrocode, developed at Los Alamos National Laboratory (Los Alamos, NM), can be used for impact cratering simulations by verifying FLAG against two analytical models of aluminum-on-aluminum impacts at different impact velocities and validating FLAG against a glass-into-water laboratory impact experiment. Our verification results show good agreement with the theoretical maximum pressures, with relative errors as low in magnitude as 1.00%. Our validation results demonstrate FLAG's ability to model various stages of impact cratering, with crater radius relative errors as low as 3.48% and crater depth relative errors as low as 0.79%. Our mesh resolution study shows that FLAG converges at resolutions low enough to reduce the required computation time from about 28 h to about 25 min. We anticipate that FLAG can be used to model larger impact cratering problems with increased accuracy and decreased computational cost on current systems relative to other hydrocodes tested by Pierazzo et al. (2008, “Validation of Numerical Codes for Impact and Explosion Cratering: Impacts on Strengthless and Metal Targets,” MAPS, 43(12), pp. 1917–1938).