Michael Müller

Mr. Michael Müller

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 July 2023 in Journal of Materials Science
Verified
Journal Article
Open access
PDF file
MMMichael Müller
Michael Müller
KFK. Franz
K. Franz
MRM. Riede
M. Riede
ELE. López
E. López
FBF. Brueckner
F. Brueckner
CLC. Leyens
C. Leyens
In laser-based directed energy deposition (L-DED) of Inconel 718 the microstructure of the fabricated components strongly depends on the applied process parameters and the resulting solidification conditions. Numerous studies have shown that the process parameters deposition speed and laser power have a major influences on microstructural properties, such as dendrite morphology and segregation behavior. This study investigates how changes in these process parameters affect the microstructure and hardness when the line mass, and thus the resulting layer height, are kept constant. This enables the microstructural comparison of geometrically similar specimens that were manufactured with the same number of layers but severely different process parameters. This approach yields the benefit of almost identical geometrical boundary conditions, such as the layer-specific build-height and heat conducting cross section, for all specimens. For microstructural analysis scanning electron microscopy and energy dispersive X-ray spectroscopy were applied and the results evaluated in a quantitative manner. The microstructural features primary dendritic arm spacing, fraction and morphology of precipitated Laves phase as well as the spatially resolved chemical composition were measured along the build-up direction. The occurring cooling rates were calculated based on the primary dendritic arm spacing using semi-empirical models. Three different models used by others researchers were applied and evaluated with respect to their applicability for L-DED. Finally, microhardness measurements were performed for a baseline evaluation of the influence on the materials’ mechanical properties.

22 December 2022 in Journal of Laser Applications
Verified
Journal Article
Open access
PDF file
MMMichael Müller
Michael Müller
CLC. C. Labisch
C. C. Labisch
LGL. Gerdt
L. Gerdt
LBL. Bach
L. Bach
MRM. Riede
M. Riede
CLC. Leyens
C. Leyens
Laser-based direct energy deposition (L-DED) with blown powder enables the simultaneous or sequential processing of different powder materials within one component and, thus, offers the possibility of additive multimaterial manufacturing. Therefore, the process allows a spatially resolved material allocation and fabrication of sharp or even graded material transitions. Within this contribution, the latest results from two major research fields in multimaterial L-DED—(I) automation and (II) rapid alloy development of high entropy alloys (HEAs) by in situ synthesis—shall be presented. First, an automated multimaterial deposition process was developed, which enables the automated manufacturing of three-dimensionally graded specimens. For this, a characterization of the deposition system regarding powder feeding dynamics and resulting powder mixtures in the process zone was conducted. The obtained system characteristics were used to achieve a three-dimensional deposition of specified powder mixtures. The fabricated specimens were analyzed by energy-dispersive x-ray spectroscopy, scanning electron microscopy, and micro hardness measurement. The research demonstrates the increasing readiness of L-DED for the fabrication of multimaterial components. Second, the latest results from rapid alloy development for HEAs by DED are presented. By the simultaneous usage of up to four powder feeders, a vast range of alloy compositions within the Al–Ti–Co–Cr–Fe–Ni HEA system was investigated. For this, tailored measurement systems such as an in-house developed powder sensor were beneficially used. The study shows the influence of a variation of Al on the phase formation and resulting mechanical properties and demonstrates the potential of L-DED for reducing development times for new alloys.

27 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
MMMichael Müller
Michael Müller
BHBastian Heinen
Bastian Heinen
MRMirko Riede
Mirko Riede
ELElena Lopez
Elena Lopez
FBFrank Brückner
Frank Brückner
CLChristoph Leyens
Christoph Leyens
The additive manufacturing (AM) technique, laser metal deposition (LMD), combines the advantages of near net shape manufacturing, tailored thermal process conditions and in situ alloy modification. This makes LMD a promising approach for the processing of advanced materials, such as intermetallics. Additionally, LMD allows the composition of a powder blend to be modified in situ. Hence, alloying and material build-up can be achieved simultaneously. Within this contribution, AM processing of the promising high-temperature material β-NiAl, by means of LMD, with elemental powder blends, as well as with pre-alloyed powders, was presented. The investigations showed that by applying a preheating temperature of 1100 °C, β-NiAl could be processed without cracking. Additionally, by using pre-alloyed, as well as elemental powders, a single phase β-NiAl microstructure can be achieved in multi-layer build-ups. Major differences between the approaches were found within substrate near regions. For in situ alloying of Ni and Al, these regions are characterized by an inhomogeneous elemental distribution in a layerwise manner. However, due to the remelting of preceding layers during deposition, a homogenization can be observed, leading to a single-phase structure. This shows the potential of high temperature preheating and in situ alloying to push the development of new high temperature materials for AM.

25 July 2024 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
MMMichael Müller
Michael Müller
LGLeonid Gerdt
Leonid Gerdt
SSSusanne Schrüfer
Susanne Schrüfer
MRMirko Riede
Mirko Riede
ELElena López
Elena López
CLChristoph Leyens
Christoph Leyens
Within this study, the alloy NiAl–2.5Ta–7.5Cr is investigated as a new matrix material for cBN-reinforced abrasive turbine blade tip coatings as currently used NiCoCrAlY matrix alloys suffer from insufficient strength at the high operating temperatures. Laser-based directed energy deposition with blown powder was applied to produce cBN reinforced NiAl-based coatings on monocrystalline CMSX-4 substrates. For this, powdery titanium-coated cBN and NiAl–2.5Ta–7.5Cr material were co-injected into the process zone to achieve an in situ formation of a NiAl–2.5Ta–7.5Cr/cBN composite. In order to overcome challenges such as cracking susceptibility, inductive preheating of the substrate up to 800 °C was used. Optical and scanning electron microscopy, energy dispersive X-ray spectroscopy, as well as electron backscatter diffraction were applied to analyse the fabricated samples’ microstructure. Additionally, the mechanical properties were evaluated by means of microhardness mappings. This work demonstrates the feasibility of in situ forming a metal matrix composite with a homogeneous distribution of cBN particles. The results show the beneficial effect of high-temperature preheating on the crack formation. However, the study also reveals challenges such as cracking induced by the injected cBN particles as well as severe intermixing of substrate and coating, which yields spatially resolved deviations in the chemical composition and resulting variations in microstructure and hardness. Graphical

28 September 2021 in Advanced Engineering Materials
Verified
Journal Article
Open access
PDF file
MMMichael Müller
Michael Müller
ASAndré Stellmacher
André Stellmacher
MRMirko Riede
Mirko Riede
ELElena López
Elena López
FBFrank Brueckner
Frank Brueckner
CLChristoph Leyens
Christoph Leyens
Recently, the additive manufacturing (AM) technology laser metal deposition (LMD) has gained a lot of attention for processing crack prone high temperature materials such as nickel‐based superalloys or intermetallics. A feasibility study on LMD of a graded transition from binary ß‐NiAl to Ni50Al42Ta8 is presented with the aim to show the possibility of manufacturing ß‐NiAl‐based structures with a spatially resolved microstructure and subsequently tailored mechanical properties. For achieving this, the alloys Ni50Al50 and Ni50Al42Ta8 are coinjected into the process zone and the powder feeding rates are adapted in a layerwise manner. Due to preheating temperatures of up to 1000 °C, the transition can be manufactured with high relative density and a low degree of cold cracking. Scanning electron microscopy of the transition zone shows the formation of a fine dendritic microstructure consisting of ß‐NiAl dendritic and NiAlTa interdendritic regions. Large area energy‐dispersive X‐ray analysis reveals a gradient in NiAlTa Laves phase content with increasing build height. The observed volume fraction of Laves phase corresponds well to reported values from cast ingots. Finally, hardness measurements along the build‐up direction show an increase in hardness from 300 HV0.1 to 680 HV0.1 indicating a tremendous increase in tensile strength.

26 January 2024 in Journal of Laser Applications
Verified
Journal Article
Open access
PDF file
ASAlex Selbmann
Alex Selbmann
SGSamira Gruber
Samira Gruber
MPMartin Propst
Martin Propst
TDTim Dorau
Tim Dorau
RDRobert Drexler
Robert Drexler
CLChristoph Leyens
Christoph Leyens
This contribution addresses the complete process chain of an annular aerospike breadboard engine fabricated by laser powder bed fusion using the nickel-based superalloy Inconel® 718. In order to qualify the material and process for this high-temperature application, an extensive material characterization campaign including density and roughness measurements, as well as tensile tests at room temperature, 700, and 900 °C, was conducted. In addition, various geometric features such as triangles, ellipses, and circular shapes were generated to determine the maximum unsupported overhang angle and geometrical accuracy. The results were taken into account in the design maturation of the manifold and the cooling channels of the aerospike breadboard engine. Postprocessing included heat treatment to increase mechanical properties, milling, turning, and eroding of interfaces to fulfill the geometrical tolerances, thermal barrier coating of thermally stressed surfaces for better protection of thermal loads, and laser welding of spike and shroud for the final assembly as well as quality assurance. This contribution goes beyond small density cubes and tensile samples and offers details on the iterations necessary for the successful printing of large complex shaped functional parts. The scientific question is how to verify the additive manufacturing process through tensile testing, simulation, and design iterations for complex geometries and reduce the number of failed prints.