Bethwel Tarus

Mr. Bethwel Tarus


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2016 in Alexandria Engineering Journal
Verified
Journal Article
Open access
BTBethwel Tarus
Bethwel Tarus
NFNermin Fadel
Nermin Fadel
AAAffaf Al-Oufy
Affaf Al-Oufy
MEMAGDI ELMESSIRY
MAGDI ELMESSIRY
Cellulose Acetate (CA) and Poly (Vinyl Chloride) (PVC) nanofiber mats were electrospun into nanofibers. The morphology and mechanical properties of nanofiber mats were evaluated versus different solution concentrations. Solutions were prepared in mixed solvent systems of 2:1 (w/w) Acetone/N,N-Dimethylacetamide (DMAc) and 3:2 (w/w) Acetone/N,N-Dimethylformamide (DMF) for CA and 1:1 (w/w) Tetrahydrofuran/DMF for PVC. Scanning electron microscopy (SEM) images revealed that a beaded fibrous structure could be electrospun beginning at 10% CA in both Acetone/DMAc and Acetone/DMF solvent systems. The experimental results showed that smooth fibers were achievable at 14% CA in Acetone/DMAc and at 16% CA in Acetone/DMF solvent systems. For PVC, beaded fibers were formed at 12% PVC and smooth fibers were formed beginning at 14% PVC. Tensile strength tests showed that mechanical properties of the nonaligned nanofiber mats were influenced by solution concentration. With increasing solution concentration, the tensile strengths, break strains and initial moduli of the CA nanofiber mats increased. The effect of solution concentration on the tensile strengths of nanofiber mats was quite significant while it did not have any considerable effect on the tensile properties of the cast films

20 February 2019 in SN Applied Sciences
Verified
Journal Article
Open access
PDF file
BTBethwel Tarus
Bethwel Tarus
JMJosphat I. Mwasiagi
Josphat I. Mwasiagi
NFNermin Fadel
Nermin Fadel
AAAffaf Al-Oufy
Affaf Al-Oufy
MEMAGDI ELMESSIRY
MAGDI ELMESSIRY
Nanofiber mats of poly(vinyl chloride) (PVC) and cellulose acetate (CA) encapsulated with silver (Ag) nanoparticles were fabricated via electrospinning for potential use as antimicrobial food packaging materials. 16 wt% PVC was prepared in 1:1 w/w tetrahydrofuran—N,N-dimethylformamide while 16 wt% CA was prepared in 3:2 (w/w) Acetone—N,N-dimethylformamide. Scanning electron microscopy analysis showed that thinner fibers could be electrospun from cellulose acetate as compared to poly(vinyl chloride) at the same solution concentrations with fiber diameters ranging from 70 to 130 nm for cellulose acetate and 180–340 nm for poly(vinyl chloride). Nanofiber diameter reduced with addition and increase of silver nanoparticles from 0 to 1 wt%. Due to the smaller cellulose acetate nanofiber diameter, its mats had lower air permeability rates. Tensile strength tests indicated that the nanofiber mats had marginal to good tensile strength values relative to film based packaging materials. Antimicrobial examination of the nanofiber mats against yeast and mould indicated that there was inhibited growth of the microorganisms on mats containing silver nanoparticles.

1 January 2020 in Journal of Engineered Fibers and Fabrics
Verified
Journal Article
Open access
PDF file
BTBethwel Tarus
Bethwel Tarus
NFNermin Fadel
Nermin Fadel
AAAffaf Al-Oufy
Affaf Al-Oufy
MEMagdi El-Messiry
Magdi El-Messiry
Nanofiber membranes are extensively used in ultra- and micro-filtration purposes due to their high surface-to-volume ratio. However, nanofiber membranes do not have adequate strength to withstand forces acting on the filter surface, especially when using very low porosity membranes. In this study, PVC nanofiber mats and nanofiber composite membranes were fabricated through electrospinning and solvent casting technology. The membranes were characterized using scanning electron microscopy (SEM), porosimetry, and tensile strength tests. Analysis indicated that electrospun mats contain varying pore sizes (nano to micro) whose frequencies within the mat vary with fiber diameter. It was also established that mats fabricated from low solution concentration contain the largest percentage of pores. The mats’ tensile strength varied with fiber packing density, fiber assembly, and the density of fiber-to-fiber contact points. The tensile properties of the nanofiber composite membranes were found to be between those of the constituents and changed with change in the nanofiber layer thickness. The fabricated nanofiber composite membranes are intended for use in applications such as air ultra-filtration, acoustic filtration etc. The high porosity and small mesh pore size of electrospun nanofiber mats allow for removal of ultra-fine particles or microbes from contaminated air, water or other media.