Filtration of aerosol particles using composites of nano- and microsized fibrous structures is a promising method of effective separation of nanoparticles from gases. The multiscale physical system describing the flow pattern and particles deposition in it requires other than a continuous approach for the process analysis. The lattice-Boltzmann method was used for the calculation of deposition efficiency on nanosized particles for the system consisting of two nano- and microsized fibers. The proposed method allows to calculate the deposition efficiency of nanoparticles on both fibers for a very wide range of Knudsen numbers in the case of each nanofiber considering molecular, slip, and continuous flow patterns. The nanofiber is a significant attractor for collecting particles as an element of multiscale fibers of the filtration composite. The results of particle deposition efficiency calculated for the microfiber, using proposed method, are similar to those obtained from the classical continuum approach ( Filippova and Hanel 1997 Filippova, O. and Hanel, D. 1997. Lattice-Boltzmann Simulation of Gas-Particle Flow in Filters. Computers and Fluids, 26: 697–712. [Crossref], [Web of Science ®] [Google Scholar] ; Przekop et al. 2003 Przekop, R. , Moskal, A. and Gradoń, L. 2003. Lattice-Boltzmann Approach for Description of the Structure of Deposited Particulate Matter in Fibrous Filters. J. Aerosol Sci., 34: 133–147. [Crossref], [Web of Science ®] [Google Scholar] ). The proposed model was extended to calculate the performance of bilayer filter structures consisting of a nanofibrous front layer and a microfibrous backing layer of the filter. Filtration efficiency, pressure drop and quality factors for uniform and non-uniform distributions of nanofibers in the front filter layer were calculated for a wide range of Knudsen and Peclet numbers.

Pollution by plastic microparticles is rising rapidly. One avenue of human exposure to nanoparticles is through inhalation. The main source of microplastics in indoor environments, leading to unintended inhalation, is synthetic fabric used in clothing. Other sources include curtains, carpets, furniture, wall paints, and floor finishes. Occupational exposure is particularly significant in waste management and recycling operations, during exposure to high heat, during high-energy treatment of polymer composites, and during 3D printing. In outdoor environments, exposure can happen through breathing in contaminated aerosols from ocean waves or airborne particles from dried wastewater treatments. Airborne particles affect human health in various ways, including via direct interactions with the epithelium and its mucus layer after deposition in the mouth and respiratory system. Exposure due to the ingestion of microplastics present in various environmental compartments may occur either directly or indirectly via the food chain or drinking water. This study aimed to determine the effects of plastic microparticles on the rheology of mucus and saliva, and, thus, their functioning. The experiments used artificial mucus, saliva, and plastic nanoparticles (namely, PS—polystyrene and PE—polyethylene). The rheological properties of saliva and mucus were determined via the use of an oscillatory rheometer at various temperatures (namely, 36.6 °C and 40 °C, which correspond to healthy and ill humans). The results were compared with those obtained for pure saliva and mucus. An increase in apparent viscosity was observed for saliva, which is behavior typical of for solid particle suspensions in liquids. In contrast, for mucus, the effect was the opposite. The influence of the presence of the particles on the parameters of the constitutive viscosity equations was studied. Plastic micro- and nanoparticles in the saliva and mucus may interfere with their physiological functions.

This study proposes utilising the solution blow-spinning process (SBS) for manufacturing a biodegradable filtration structure that ensures high efficiency of particle filtration with an acceptable pressure drop. The concept of multi-layer filters was applied during the design of filters. Polylactic acid (PLA) was used to produce various layers, which may be mixed in different sequences, building structures with varying filtration properties. Changing the process parameters, one can create layers with diverse average fibre diameters and thicknesses. It enables the design and creation of optimal filtration materials prepared for aerosol particle filtration. The structures were numerically modelled using the lattice Boltzmann approach to obtain detailed production guidelines using the blow-spinning technique. The advantage of this method is the ability to blow fibres with diameters in the nanoscale, applying relatively simple and cost-effective equipment. For tested PLA solutions, i.e., 6% and 10%, the mean fibre diameter decreases as the concentration decreases. Therefore, the overall filtering efficiency decreases as the concentration of the used solution increases. The produced multi-layer filters have 96% overall filtration efficiency for particles ranging from 0.26 to 16.60 micrometres with a pressure drop of less than 160 Pa. Obtained results are auspicious and are a step in producing efficient, biodegradable air filters.