Martin Necpal

Dr. Martin Necpal

Slovak University of Technology in Bratislava, Faculty of Materials Science and Technology in Trnava
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 January 2022 in Materials
Verified
Journal Article
Open access
PDF file
Marcel KurucMarcel Kuruc
Marcel Kuruc
TVTomáš Vopát
Tomáš Vopát
Jozef PeterkaJozef Peterka
Jozef Peterka
MNMartin Necpal
Martin Necpal
VŠVladimír Šimna
Vladimír Šimna
FJFrantišek Jurina
František Jurina
The paper deals with the issue of cutting zone and chip compression. The aim was to analyse the microstructure transverse section of the cutting zone on a metallographic cut, due to determined values of chip compression and plastic deformation, which affect the cutting process efficiency. The tested cutting tool material was coated with cemented carbide. The selected workpiece materials were C45 medium carbon steel of ISO grade and 62SiMnCr4 tool steel of ISO (W.Nr. 1.2101) grade. In the experiments, a DMG CTX alpha 500 turning centre was used. The cutting speed and feed were varied, and the depth of the cut was kept constant during the turning. The plastic deformation and chip compression determine the efficiency of the cutting process. The higher compression requires more work to perform the process and, therefore, it requires more energy for doing so. With the increase of the cutting speed, the deformation for C45 steel is decreased. The rapid deformation reduction was observed when the cutting speed was increased from 145 m/min to 180 m/min. Generally, deformation is decreasing with the increase of the feed. Only at a cutting speed of 145 m/min was the deformation elevation observed, when the feed was increased from 0.4 mm to 0.6 mm. During the turning of the 62SiMnCr4 tool steel we observed an error value at a cutting speed of 145 m/min and a feed of 0.4 mm was the middle cutting parameter. However, feed dependence was clear: With an increase of the feed, the plastic deformation was decreasing. This decreasing was more rapid with the increasing of the cutting speed. Besides plastic deformation, there was analysed chip compression as well. With the increasing of the cutting speed, there was a decrease of the chip compression. Due to a lack of information in the area of the chip compression and the plastic deformation in the cutting process, we decided to investigate the cutting zone for the turning of tool steels 62SiMnCr4, which was compared with the reference steel C45. The results could be applied to increase the efficiency of the process and improvement of the surface integrity.

27 October 2023 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
Michal SkarbaMichal Skarba
Michal Skarba
MPMarcela Pekarcikova
Marcela Pekarcikova
LFLubomír Frolek
Lubomír Frolek
ECEva Cuninková
Eva Cuninková
MNMartin Necpal
Martin Necpal
ŠŠŠtefan Šimon
Štefan Šimon
Alternating current (AC) losses in superconducting tapes (SCTs) are one of the main concerns for their use in applications where costs of heat dissipation need to be reduced, such as pulse magnets. Modification of the tapes by striation has been shown to significantly reduce AC losses, and several filamentization methods have been developed. Up to two orders of magnitude decrease in AC losses was reported in previous works with laser ablation, mechanical grooving, or chemical etching. However, a different approach may have to be used to achieve similar results for those SCTs (or their applications after striation), which are more prone to degradation by the side effects of the mentioned methods. We proposed a procedure based on chemo-mechanical etching, which avoids problems arising from thermal degradation and mechanical pressure. Our method intended for the REBCO (RE = rare earth metal, B = Ba, C = Cu, O = oxygen) based high-temperature SCTs yielded low and reproducible AC losses, low cost, retention of the relative critical current up to 93%, and preservation of the mechanical properties of the tape substrate.

31 August 2018 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
JMJana Moravčíková
Jana Moravčíková
RMRoman Moravčík
Roman Moravčík
MKMartin Kusy
Martin Kusy
MNMartin Necpal
Martin Necpal

25 November 2023 in Materials
Verified
Journal Article
Open access
PDF file
MPMarcela Pekarcikova
Marcela Pekarcikova
LFLubomír Frolek
Lubomír Frolek
MNMartin Necpal
Martin Necpal
ECEva Cuninková
Eva Cuninková
Michal SkarbaMichal Skarba
Michal Skarba
BLBarbora Ludrovcová
Barbora Ludrovcová
This study aimed to enhance the performance of Ag-stabilized high-temperature superconducting (HTS) tapes with a focus on reducing magnetization losses. Two approaches were employed: dividing the tapes into narrower widths and introducing striation at the level of the superconducting layer. The process of laser ablation proved to be an effective method for implementing these modifications. The quality of the cut edges and grooves was assessed using scanning electron microscopy. To evaluate the electrical properties, measurements were conducted on the critical current and magnetization loss in samples at different stages: in their initial state, after cutting, and after the striation process. Of the two modifications, the striation process more effectively reduced the AC losses in the HTS tapes, approximately by one order of magnitude. The retention of critical current remained high after cutting, but varied with the number of created filaments after the striation process. Subsequently, a short cable was wound from the cut and striated HTS tape. This cable demonstrated a remarkable sixfold reduction in AC losses compared to the initial HTS tape.

1 March 2018 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
JŠJana Šugárová
Jana Šugárová
PŠPeter Šugár
Peter Šugár
MFMartin Frnčík
Martin Frnčík
MNMartin Necpal
Martin Necpal
JMJana Moravčíková
Jana Moravčíková
MKMartin Kusy
Martin Kusy
The morphological texturing of forming tool surfaces has high potential to reduce friction and tool wear and also has impact on the surface layers properties of formed material. In order to understand the effect of different types of tool textures, produced by nanosecond fibre laser, on the...

23 February 2021 in Materials
Verified
Journal Article
Open access
PDF file
Michal SkarbaMichal Skarba
Michal Skarba
MPMarcela Pekarcikova
Marcela Pekarcikova
LFLubomír Frolek
Lubomír Frolek
ECEva Cuninková
Eva Cuninková
MNMartin Necpal
Martin Necpal
We prepared overlap soldered joints of high-temperature superconducting tapes, using various materials and preparation conditions. In order to select the joints with optimal performance, we correlated their electrical properties (derived from current–voltage curves) with the microstructure of the respective joint cross-section by scanning electron microscopy. With the first group of joints, we focused on the effect of used materials on joint resistivity and critical current, and we found that the dominant role was played by the quality of the internal interfaces of the superconducting tape. Initial joint resistivities ranged in the first group from 41 to 341 nΩ·cm2. The second group of joints underwent a series of thermal cyclings, upon which the initial resistivity range of 35–49 nΩ·cm2 broadened to 25–128 nΩ·cm2. After the total of 135 thermal cycles, three out of four joints showed no signs of significant degradation. Within the limit of 100 thermal cycles, reliable soldered joints can be thus prepared, with normalized resistivity not exceeding 1.4 and with normalized critical current above the value of 0.85.