We investigated the effect of CMC dosage on dispersibility and sedimentation of FeS,and the effects of initial Cr(VI) concentrations,reaction temperatures and initial pH values on the Cr(VI) removal by Nano-FeS and CMC-FeS through experiments.At the same time, the migration performance and deposition of Nano-FeS and CMC-FeS under different conditions were investigated.The results showed that: Nano-FeS aggregated to floc and precipitated.The 2.4% CMC-FeS had good dispersibility and anti-settling capacity.With the initial concentration of Cr(VI) increased from 10mg·L-1 to 50mg·L-1,the Cr(VI) removal efficiencies of Nano-FeS and CMC-FeS decreased.CMC prolonged reaction time between FeS and Cr(VI).When the reaction temperature increased from 10°C to 25°C,and the promotion of Cr(VI) reduction by CMC-FeS was higher than that of Nano-FeS.When the initial pH was 3-9,the Cr(VI) removal efficiencies of Nano-FeS and CMC-FeS were almost similar. But Cr(VI) removal by CMC-FeS was significantly higher than by Nano-FeS 23% at pH 12,which indicated that CMC-FeS still had high removal ability for Cr(VI) at high pH. From the breakthrough curves,the penetration ability (Ci/C0) of the two kinds of FeS nanoparticles in coarse,medium and fine sand was CMC-FeS > Nano-FeS. The maximum transport distance (Lmax) of CMC-FeS was 6.4 times longer than that of Nano-FeS in medium sand. The increase of FeS injection concentration resulted in more FeS deposition into the media,but the CMC modification could significantly reduce the deposition rate (k) and amount of deposition.
The growing use of nanoscale zero-valent iron (NZVI) in the remediation of contaminated groundwater raises concerns regarding its transport in aquifers. Laboratory-scale sand-packed column experiments were conducted with bare and sucrose-modified NZVI (SM-NZVI) to improve our understanding of the transport of the nanoparticles in saturated porous media, as well as the role of media size, suspension injection rate and concentration on the nanoparticle behavior. As the main indicative parameters, the normalized effluent concentration was measured and the deposition rate coefficient (k) was calculated for different simulated conditions. Overall, compared to the high retention of bare NZVI in the saturated silica column, SM-NZVI suspension could travel through the coarse sand column easily. However, the transport of SM-NZVI particles was not very satisfactory in a smaller size granular matrix especially in fine silica sand. Furthermore, the value of k regularly decreased with the increasing injection rate of suspension but increased with suspension concentration, which could reflect the role of these factors in the SM-NZVI travel process. The calculation of k-value at the tests condition adequately described the experimental results from the point of deposition dynamics, which meant the assumption of first-order deposition kinetics for the transport of NZVI particles was reasonable and feasible.
Dyes are common contaminants, some of which are teratogenic, carcinogenic, and causative of ecological damage, and dye wastewater often contains toxic sulfides. Biochar has been widely used for the adsorption and catalysis degradation of pollutants, including dyes and sulfides, due to its abundant surface functional groups and large specific surface area. Therefore, the simultaneous treatment of dyes and sulfides with biochar may be a feasible, effective, and novel solution. This study sought to utilize low-cost, environmentally friendly, and widely sourced biochar materials from agricultural wastes such as corn stalk, rice chaff, and bean stalk to promote the reduction of dyes by sulfides. Through the action of different biochars, sulfides can rapidly decompose and transform oxidizing dyes. The RCB800 (rice chaff biochar material prepared at 800 °C) was observed to have the best effect, with a degradation rate of 96.6% in 40 min and 100% in 50 min for methyl orange. This series of materials are highly adaptable to temperature and pH, and the concentration of sulfides has a significant effect on degradation rates. Compared with commercial carbon materials, biochars are similar in terms of their catalytic mechanism and are more economical. Scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption and desorption characterization results indicated that biochar contains more pores, including mesopores, and a sufficient specific surface area, both of which are conducive to the combination of sulfides and dyes with biochar. X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy showed that there are oxygen-containing functional groups (examples include quinones and carboxyl groups) on the surface of biochar that promote the reaction of sulfide and dye. The formation of active polysulfides also potentially plays an important role in the degradation reaction. This article outlines a new method for improving the degradation efficiency of azo dyes and sulfides via biochar materials derived from widely sourced agricultural wastes.