Temperature is an important factor to aggravate the insulation degradation of metallized film capacitors, in order to study the effect of temperature on the partial discharge characteristics of biaxially oriented polypropylene (BOPP) film under nanosecond pulse voltage, the partial discharge measurement of BOPP film was carried out at varying temperatures (25 °C~100 °C) and with different rising times (15~115 ns). It is found that the repetitive partial discharge inception voltage (RPDIV) and partial discharge time-lag gradually decrease with the increase of temperature, while the number of partial discharges and the amplitude of discharges in the falling stage of the pulse show a monotonically increasing trend; the amplitude of discharges in the rising stage of the pulse increases, then decreases and then increases again with the increase of temperature, and there are the local maximum and local minimum at 55°C and 85°C, respectively. Meanwhile, based on the thermal field emission effect, the quantitative mathematical relationship between the partial discharge statistical characteristics and temperature is established for the first time. The results are expected to provide experimental basis and mechanism explanation for the reliability assessment and insulation performance improvement of dielectric insulation for energy storage under extreme conditions.
18 January 2023 in IEEE Transactions on Plasma Science
Film capacitors are used as the key energy storage device for high-power pulse generators, and partial discharge (PD) is an important factor leading to insulation degradation and the failure of film capacitors. To accurately evaluate the effect of the rise rate on PD under nanosecond pulse voltage, experiments on the PD characteristics of biaxially oriented polypropylene (BOPP) films under high rise rate (18.3–140 V/ns) nanosecond pulse voltages were carried out. The PDs were mostly concentrated in the rising and falling phases of the nanosecond pulse. Moreover, the repetitive PD inception voltage (RPDIV) first increased and then remained unchanged as the rise time increased, and the PD amplitude and the number of discharges in the rising phase of the nanosecond pulse increased as the rise rate increased, while the discharge time lag decreased gradually. The PD amplitude, the number of discharges, and the discharge time lag in the falling phase of the nanosecond pulse all increased as the rise rate increased. In addition, when the rise rate was less than 50 V/ns, the PD statistical characteristics changed rapidly as the rise rate increased, and when the rise rate was greater than 50 V/ns, the PD statistical characteristics gradually changed more slowly as the rise rate increased.
Partial discharge (PD) is one of the key factors leading to premature insulation failure of film capacitors used in pulse power devices. To study the effect of frequency on the PD characteristics of biaxially oriented polypropylene (BOPP) film, a sphere-plate electrode was used to simulate defects of the air gap between the film layers. PD experiments of the BOPP film were carried out under 1, 10, 100, 500 Hz, and 1 kHz with a rising edge of 65 ns and a pulse width of 300 ns. The results show that the repetitive partial discharge inception voltage (RPDIV), the number of discharges, the rising stage discharge (RSD) amplitude, and the falling stage discharge (FSD) time-lag, all show an increase and then decrease with increasing pulse frequencies and reach a maximum value at a pulse frequency of 100 Hz. Moreover, the FSD discharge amplitude and the RSD discharge time-lag increase with an increasing pulse frequency. From the perspective of initial electron generation, the quantitative mathematical relationship between PD characteristics (RPDIV, PD amplitude, PD number, and PD time-lag) and frequency was established based on the Fowler–Nordheim field emission effect for the first time, which can reflect the influence of frequency on the memory effect and the development process of PD. The results can provide an experimental basis and a mechanistic explanation for the evaluation of PD characteristics for film capacitors under nanosecond pulse voltage.
Conductive polymer composites require high conductive filler loadings to achieve relatively ideal electromagnetic interference (EMI) shielding performance, which brings problems such as heavy weight and poor processability and ultimately limits their application in the aerospace field. To solve the above problems and realize the preparation of excellent EMI shielding composites with low filler loadings, a bipolar pulsed electric field-induced graphene nanoplatelets (GNPs) alignment method is proposed in this paper to improve the electrical conductivity and EMI shielding performance. The orientation and alignment of GNPs in the matrix were characterized by x-ray diffraction and scanning electron microscopy, and the results showed that GNPs formed a conductive network. The electrical conductivity of the composite material in the X-band was measured, and the results showed that the bipolar pulsed electric field could significantly improve the electrical conductivity of the composite material; the improvement percentage reached 100%–300% under the five filler loadings. In addition, the EMI shielding effectiveness of the composite material in the X-band was tested. The results showed that the EMI shielding effectiveness of the composite material with a mass fraction of 14% increased from 16.48–15.86 dB to 21.37–20.99 dB with the action of the bipolar pulsed electric field, and the improvement percentage was 32%. This is the first study on improving the EMI shielding performance of composite materials by applying a bipolar pulsed electric field, and it provides an effective method to prepare EMI shielding composites with low filler loadings.
Using a nanosecond pulsed electric field to induce orientation and arrangement of insulating flake particles is a novel efficient strategy, but the specific mechanism remains unclear. In this study, the dielectrophoretic motion of boron nitride nanosheets (BNNSs) in ultrapure water under a nanosecond pulsed electric field is simulated for the first time. First, the simulation theory is proposed. When the relaxation polarization time of the dielectric is much shorter than the pulse voltage width, the pulse voltage high level can be considered a short-term DC voltage. On this basis, the Arbitrary Lagrangian–Euler (ALE) method is used in the model, considering the mutual ultrapure water–BNNS particles-nanosecond pulsed electric field dielectrophoretic interaction, to study the influence of different BNNSs self-angle α and relative angle β on local orientation and global arrangement. The particles are moved by the dielectrophoretic force during the pulse voltage high level and move with the ultrapure water flow at the zero level, without their movement direction changing during this period, so the orientation angle and distance changes show step-like and wave-like curves, respectively. The model explains the basic mechanism of dielectrophoretic motion of BNNSs under a pulsed electric field and summarizes the motion law of BNNSs, providing a reference for subsequent research.
30 October 2024 in Journal of Physics D: Applied Physics
Epoxy resin composites are widely used as insulating and supporting materials in high-voltage power systems due to their excellent mechanical and electrical properties. However, long-term operation under high-voltage direct current induces surface flashover. Plasma enhanced chemical vapor deposition (PECVD) has been shown to effectively improve the surface insulation properties of epoxy resin. However, the influence of substrate temperature on the film composition, stress, morphology, and surface flashover performance remains unclear. This study uses PECVD to treat epoxy resin, enhancing its surface flashover performance. Tetraethoxysilane is used as the precursor to deposit nano-scale SiOx films on the epoxy resin surface. The effects of different substrate temperatures on the surface flashover voltage, physicochemical properties, and mechanical properties of epoxy resin are characterized. The results show that the surface flashover voltage increases and then saturates with increasing substrate temperature, improving by 27.4% at 60 °C compared to untreated samples. The surface roughness of epoxy resin decreases after plasma deposition, while highly oxidized silicon-containing functional groups are introduced. When the substrate temperature increases from 20 °C to 60 °C, the interfacial bonding strength improves by 25.9%. This study provides a simple, efficient, and controllable method to enhance the surface flashover performance of epoxy resin, promoting the application of this technology in engineering practice.