Wei Deng

Dr. Wei Deng

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 March 2021 in Polymers
Verified
Journal Article
Open access
PDF file
WWWenqi Wang
Wenqi Wang
GRGuanguan Ren
Guanguan Ren
MZMing Zhou
Ming Zhou
Wei DengWei Deng
Wei Deng
Dielectric elastomer (DE) is a type of electric field type electroactive polymer material that can produce greater deformation under the action of an electric field and has a faster recovery speed. It has the advantages of high energy density, large strain, low quality, and commercialization, and has become the most widely concerned and researched electroactive polymer material. In this study, copper calcium titanate (CCTO) particles with a large dielectric constant were selected as the filling phase, and a silicone rubber (PDMS) with better biocompatibility and lower elastic modulus was used as the matrix to prepare CCTO/PDMS, which is a new type of dielectric elastomer material. The structure of the dielectric elastomer is analyzed, and its mechanical properties, dielectric properties, and driving deformation are tested. Then, KH550, KH560, and KH570 modified CCTO is used in order to improve the dispersibility of CCTO in PDMS, and modified particles with the best dispersion effect are selected to prepare dielectric elastomer materials. In addition, mechanical properties, dielectric properties, and driving deformation are tested and compared with the dielectric elastomer material before modification. The results show that as the content of CCTO increases, the dielectric constant and elastic modulus of the dielectric elastomer also increase, and the dielectric loss remains basically unchanged at a frequency of 100 Hz. When the filling amount reaches 20 wt%, the dielectric constant of the CCTO/PDMS dielectric elastomer reaches 5.8 (100 Hz), an increase of 120%, while the dielectric loss at this time is only 0.0038 and the elastic modulus is only 0.54 MPa. When the filling amount is 5 wt%, the dielectric elastomer has the largest driving deformation amount, reaching 33.8%. Three silane coupling agents have been successfully grafted onto the surface of CCTO particles, and the KH560 modified CCTO has the best dispersibility in the PDMS matrix. Based on this, a modified CCTO/PDMS dielectric elastomer was prepared. The results show that the improvement of dispersibility improves the dielectric constant. Compared with the unmodified PDMS, when the filling content is 20 wt%, the dielectric constant reaches 6.5 (100 Hz). Compared with PDMS, it has increased by 150%. However, the improvement of dispersion has a greater increase in the elastic modulus, resulting in a decrease in its strain parameters compared with CCTO/PDMS dielectric elastomers, and the electromechanical conversion efficiency has not been significantly improved. When the filling amount of modified CCTO particles is 5 wt%, the dielectric elastomer has the largest driving deformation, reaching 27.4%.

10 January 2022 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
JCJiajian Chen
Jiajian Chen
Wei DengWei Deng
Wei Deng
YRYuanyuan Ren
Yuanyuan Ren
KQKexin Qu
Kexin Qu
GLGuoan Li
Guoan Li

16 August 2022 in IEEE Transactions on Dielectrics and Electrical Insulation
Verified
Journal Article
Closed access
Wei DengWei Deng
Wei Deng
YRYuanyuan Ren
Yuanyuan Ren
KQKexin Qu
Kexin Qu
HZHong Zhao
Hong Zhao
Voltage stabilizers have the potential to improve the overall insulation properties of polymeric cables, but the poor compatibility with the polymer matrix limits their practical application. In this work, the reaction of 2,4-dihydroxybenzophenone (DHBP) with maleic anhydride (MAH) provides a novel and reactive aromatic ketone voltage stabilizer 4-(4-benzoyl-3-hydroxyphenoxy)-4-oxobut- 2-enoic acid denoted by MDVS, which can be grafted onto the backbone of polyethylene (PE) during the cross-linking process. The physicochemical and dc insulation properties of the cross-linked PE grafted with different addition of MDVS (XLPE-g-MDVS) are investigated, and the underlying mechanism is discussed. In comparison with the pristine XLPE, substantially suppressed space charge accumulation and decreased electrical conductivity are obtained in the XLPE-g-MDVS materials. As the content of MDVS is 1.2 wt%, XLPE-g-MDVS materials exhibit higher breakdown strength than that of the pristine XLPE. Furthermore, the graftable voltage stabilizer MDVS presents more efficient stabilizing effect than conventional voltage stabilizer DHBP before and after high-temperature degassing. Thermally stimulated current (TSC) tests and quantum chemical calculations are consistent with the experimental results of insulation properties, illustrating that capture and trap mechanisms cooperate in the improvement of XLPE dc insulation performance.

27 August 2018 in High Performance Polymers
Verified
Journal Article
Closed access
Wei DengWei Deng
Wei Deng
WYWeili Yu
Weili Yu
WCWeiwei Cui
Weiwei Cui
HGHuachao Guo
Huachao Guo
YLYifan Liu
Yifan Liu
TZTianqi Zhao
Tianqi Zhao
Polymer dielectric composites with high dielectric permittivity and low dielectric loss play an increasing important role for modern electronic and electric industry. In this study, polyvinylidene fluoride (PVDF) incorporated with expanded graphite (EG) or reduced graphene oxide (rGO) was prepared by solution casting and the following hot pressing. The structure, morphology, and properties of the obtained products were characterized. In comparison with EG, rGO exhibits well dispersion and strong interaction with PVDF matrix. With the increasing content of conductive fillers, the dielectric permittivity of both PVDF/EG and PVDF/rGO composites shows an increasing trend whereas the dielectric loss keeps at a low level. The dielectric permittivity of PVDF filled with 4 wt% EG and 8 wt% rGO reaches 420 and 38 at 100 Hz, respectively. Moreover, the introduction of EG and rGO improves the mechanical strength and the thermal stability of PVDF matrix.

19 February 2021 in High Performance Polymers
Verified
Journal Article
Closed access
PDF file
Wei DengWei Deng
Wei Deng
GRGuanguan Ren
Guanguan Ren
WWWenqi Wang
Wenqi Wang
WCWeiwei Cui
Weiwei Cui
WLWenjun Luo
Wenjun Luo
Polymer composites with high dielectric constant and thermal stability have shown great potential applications in the fields relating to the energy storage. Herein, core-shell structured polyimide@BaTiO3 (PI@BT) nanoparticles were fabricated via in-situ polymerization of poly(amic acid) (PAA) and the following thermal imidization, then utilized as fillers to prepare PI composites. Increased dielectric constant with suppressed dielectric loss, and enhanced energy density as well as heat resistance were simultaneously realized due to the presence of PI shell between BT nanoparticles and PI matrix. The dielectric constant of PI@BT/PI composites with 55 wt% fillers increased to 15.0 at 100 Hz, while the dielectric loss kept at low value of 0.0034, companied by a high energy density of 1.32 J·cm−3, which was 2.09 times higher than the pristine PI. Moreover, the temperature at 10 wt% weight loss reached 619°C, demonstrating the excellent thermostability of PI@BT/PI composites. In addition, PI@BT/PI composites exhibited improved breakdown strength and toughness as compared with the BT/PI composites due to the well dispersion of PI@BT nanofillers and the improved interfacial interactions between nanofillers and polymer matrix. These results provide useful information for the structural design of high-temperature dielectric materials.

31 May 2022 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
YRYuanyuan Ren
Yuanyuan Ren
Wei DengWei Deng
Wei Deng
WLWanyu Li
Wanyu Li
HZHong Zhao
Hong Zhao