Modern pulsewidth modulation (PWM) inverter motor drives are affected by dangerous common-mode currents due to the high rate of variation of the modulated voltage. An inexpensive alternative to low-pass filters, which are normally used to limit common-mode currents, consists in reducing such currents by using suitable modulation strategies. In this paper, a new approach for designing PWM strategies is presented, which is able to reduce common-mode currents by limiting the amount of variations of the common-mode voltage. The main characteristics of the proposed approach are experimentally evaluated on a standard PWM induction motor drive.

To obtain a full exploitation of battery potential in energy storage applications, an accurate modeling of electrochemical batteries is needed. In real terms, an accurate knowledge of state of charge (SOC) and state of health (SOH) of the battery pack is needed to allow a precise design of the control algorithms for energy storage systems (ESSs). Initially, a review of effective methods for SOC and SOH assessment has been performed with the aim to analyze pros and cons of standard methods. Then, as the tradeoff between accuracy and complexity of the model is the major concern, a novel technique for SOC and SOH estimation has been proposed. It is based on the development of a battery circuit model and on a procedure for setting the model parameters. Such a procedure performs a real-time comparison between measured and calculated values of the battery voltage while a PI-based observer is used to provide the SOC and SOH actual values. This ensures a good accuracy in a wide range of operating conditions. Moreover, a simple start-up identification process is required based on battery data-sheet exploitation. Because of the low computational burden of the whole algorithm, it can be easily implemented in low-cost control units. An experimental comparison between SOC and SOH estimation performed by suggested and standard methods is able to confirm the consistency of the proposed approach.

Power generation systems (PGSs) based on hybrid renewable energy are one of the promising solutions for future distributed generation systems. Among different configurations, hybrid photovoltaic-wind turbine (PV-WT) grid connected PGSs are the most adopted for their good performance. However, due to the complexity of the system, the optimal balance between these two energy sources requires particular attention to achieve a good engineering solution. This paper deals with the optimal sizing of PV-WT by adopting different multicriteria decision analysis (MCDA) optimization approaches. Sensitivity of MCDA algorithms has been analyzed, by considering different weighting criteria techniques with different fluctuation scenarios of wind speed and solar radiation profiles, thus highlighting advantages and drawbacks of the proposed optimal sizing approaches. The following study could be assumed as a powerful roadmap for decision makers, analysts, and policy makers.

In this paper, the design, realization, and performance evaluation of a single-phase 3-kW dc/ac power converter, using an active-bridge dc/dc converter and a full-bridge dc/ac, are introduced, presenting a novel solution on the industrial scenario for the considered application. Control algorithms, including the maximum power point tracking, paralleling to the grid, and converter switching signals, are digitally implemented on a standard microcontroller.

This paper deals with the analysis and implementation of a new scalar control technique for industrial interior permanent-magnet synchronous motor drives that exploits energy-saving capability. In particular, the proposed control strategy forces the conditions of maximum torque per ampere (MTPA), flux weakening (FW), and maximum torque per voltage (MTPV) simply by assigning polynomial relationships between the operating angles of the machine. Although the dynamic performance of the drive is worsened compared to that of vector control schemes, the modified scalar control allows us to work in energetic conditions, very close to those obtained with vector-controlled drives exploiting MTPA, FW, and MTPV strategies. The control techniques are implemented without using any speed and voltage measurement and with only a single current feedback. This paper provides a detailed study of the control strategy, showing the effectiveness and limitations of the method through simulations and experimental results.

An open-end winding machine configuration and a suitable control strategy for medium-voltage ac motor drives applications are proposed in this paper in order to reduce the distortion of phase voltages in multilevel inverters (MLIs). Differently than standard open-end winding configurations, where two inverters provide active power to both sides of the stator winding, a main MLI supplies in this case the machine on one side, while an auxiliary two-level inverter acts as active power filter on the other side. A high efficiency step modulation manages the MLI, while the auxiliary unit is pulse width modulation (PWM) operated. As the phase current harmonic content is improved, the torque ripple is reduced and the drive efficiency is increased. By exploiting the proposed approach, the apparent switching frequency of the system is that typical of a PWM inverter, although the main unit is operated according to a voltage step modulation strategy. Simulation and experimental results confirm the consistency of the proposed methodology.