By adding a cylindrical airbag on the leeward side of a cuboid pontoon, a new-type double-row floating breakwater is designed to improve the wave attenuation performance, and its hydrodynamic characteristics are studied through numerical simulations. First, based on the smoothed particle hydrodynamics (SPH) method, a numerical model used to simulate the interaction between waves and moored floating bodies is built. The fluid motion is governed by the Navier–Stokes equations. The motion of the floating body is computed according to Newton’s second law. The modified dynamic boundary condition is employed to treat the solid boundary. The lumped-mass method is adopted to implement the mooring system. Then, two physical model experiments on waves interaction with cuboid and dual cylindrical floating pontoons are reproduced. By comparing the experimental and numerical wave transmission coefficients, wave reflection coefficients, response amplitude operators and mooring force, the reliability of the numerical model is validated. Finally, the validated numerical model is applied to study the influence of separation distance and wave parameters on the hydrodynamic characteristics of the double-row floating breakwater. The results indicate that the optimal separation distance between pontoon and airbag is 0.75 times the wavelength. At such separation distance and within the concerned 1–4 m wave heights and 4–7 s wave periods, the pontoon-airbag system presents better wave attenuation performance than a single pontoon. This improvement weakens as wave height increases while it strengthens as the wave period increases. In addition, the double-row floating breakwater is more effective in a high-wave regime than in a low-wave regime. In the case of short waves, attention should be paid to the stability and mooring reliability of the seaward pontoon, while in the case of long waves, care needs to be taken of the leeward airbag.
In this paper, a yacht project in Tingjiang Town, Mawei, Fujian, is suggested as an example of a barge type breakwater made out of scrap barges. The physical modelling of a two-dimensional flume wave test was carried out on a barge-type breakwater, focusing on the wave dissipation and anchor chain forces under two different mooring methods, the “crossed tilt” mooring and the “front and rear direct pull” mooring, with no change in the size of the breakwater. The test results show that the effect of wave elimination of the barge-type breakwater gradually decreases with the increase of wave elements under different mooring conditions, but the effect of wave elimination of the barge-type breakwater is significantly better under the “crossed tilt” mooring systems than under the “front and rear direct pull” mooring systems; the maximum tension of the anchor chain under the “inner eight” diagonal mooring method is significantly higher than that under the front and rear straight pulling mooring method. The maximum anchor chain tension under the “crossed tilt” mooring system is significantly greater than that under the fore and aft straight mooring method, while the average anchor chain tension does not change significantly under the two mooring methods.
Accurate prediction of wave attenuation behind breakwaters is critical for coastal protection and offshore aquaculture operations. This study proposes TransWaveNet, a simplified model based on transformers, which aims to forecast future wave heights (12 h) behind breakwaters using historical wave height data (12 h) measured in front of breakwaters. The data are derived from synchronous wave monitoring data collected from a floating breakwater in Lianjiang County, China (15 months, hourly intervals), used to construct the TransWaveNet model. A systematic evaluation indicates that TransWaveNet outperforms LSTM (long short-term memory), ANN (artificial neural network), and Seq2Seq (sequence to sequence) baseline models in predicting significant wave height (Hs) over a 12-h period, achieving a prediction accuracy of R2 (R-squared)= 0.73, MSE (mean squared error) = 0.02 m2, and RMSE (Root Mean Square Error) = 0.142 m. The model revealed two key findings: first, the 12-h input sequence achieves an optimal balance between accuracy and computational efficiency; second, while effectively capturing the Hs decay pattern, the framework exhibits minor limitations at maximum wave height (Hmax). The framework provides a lightweight, data-driven solution for cross-breakwater wave forecasting in practical applications.
In this study, physical model tests are used to investigate the effects of a varying number of wave and current parameters, the gap ratios between the pipeline and seabed, the spacing ratios between the two pipelines and the diameter ratios on the hydrodynamic coefficients of the large, small pipeline and pipeline system (bundle) in a piggyback configuration under the combined action of waves and current. The results show that, compared with the pure wave field, the existence of the steady current will lead to a decrease in hydrodynamic coefficients. In addition, the results indicate clear differences between the hydrodynamic coefficients of the large pipeline, small pipeline and piggyback pipeline system. The experimental results on hydrodynamic coefficients can be used as an important basis for the safety design of a submarine piggyback pipeline.
To address the issue of insufficient wave dissipation capacity in standard floating breakwaters consisting of pontoons, this research proposes a combined floating breakwater with T-block connections. AQWA software is used to conduct numerical simulation studies on the dissipation characteristics of waves, and the reliability of the results is confirmed by integrating them with tests of a physical model. It is found that the transmission coefficient of the combined floating breakwater increases with the wave period. When the incident wave period T6 s, the effect is weakened; and at T=8 s, the change in height is basically unaffected. Increasing the relative width of the T-block is more significant in terms of the enhancement of the wave dissipation performance, whereas the height of the incident wave has a smaller effect on the transmission coefficient, and the transmission coefficient tends to increase with the increase of the wave height only in the case where T=8 s. The height of the incident wave has little effect on the transmission coefficient. The transmission coefficient increases with the wave height only when T=8 s; when the wave period is small (e.g. 4 s), the effect of wave elimination is enhanced by increasing the draught depth, and the draught does not have a significant effect on the wave dissipation performance when T>6 s. Compared with a typical floating pontoon breakwater with a single- and double-row arrangement, the combined floating pontoon breakwater has a better effect in terms of dissipating the waves, and its advantage is significant for a period T≤6 s, with a 44% increase in the maximum wave abatement compared to a single-row arrangement. In addition, the free-motion response is analysed to clarify the effects of different factors on the transverse and pendulum motion. This study provides an important reference for the design and application of floating pontoon breakwaters.