To apply carbon nanotubes (CNTs) as reinforcing agents in next-generation composites, it is essential to improve their nominal strength. However, since it is difficult to completely remove the defects, the synthesis guideline for improving nominal strength is still unclear, i.e., the effective strength and the number of nanotube layers required to improve the nominal strength has been undermined. In this study, molecular dynamics simulations were used to elucidate the effects of vacancies on the mechanical properties of CNTs. Additionally, the relationships between the number of layers and effective and nominal strengths of CNTs were discussed theoretically. The presence of extensive vacancies provides a possible explanation for the low nominal strengths obtained in previous experimental measurements of CNTs. This study indicates that the nominal strength can be increased from the experimentally obtained values of 10 GPa to approximately 20 GPa by using six to nine nanotube layers, even if the increase in effective strength of each layer is small. This has advantages over double-walled CNTs, because the effective strength of such CNTs must be approximately 60 GPa to achieve a nominal strength of 20 GPa.
Numerical modeling for geothermal reservoir engineering is a crucial process to evaluate the performance of the reservoir and to develop strategies for the future development. The governing equations in the geothermal reservoir models consist of several constitutive parameters, and each parameter is given to a large number of simulation grids. Thus, the combinations of parameters we need to estimate are almost limitless. Although several inverse analysis algorithms have been developed, determining the constitutive parameters in the reservoir model is still a matter of trial-and-error estimation in actual practice, and is largely based on the experience of the analyst. There are several parameters which control the hydrothermal processes in the geothermal reservoir modeling. In this study, as an initial challenge, we focus on permeability, which is one of the most important parameters for the modeling. We propose a machine-learning-based method to estimate permeability distributions using measurable data. A large number of learning data were prepared by a geothermal reservoir simulator capable of calculating pressure and temperature distributions in the natural state with different permeability distributions. Several machine learning algorithms (i.e., linear regression, ridge regression, Lasso regression, support vector regression (SVR), multilayer perceptron (MLP), random forest, gradient boosting, and the k-nearest neighbor algorithm) were applied to learn the relationship between the permeability and the pressure and temperature distributions. By comparing the feature importance and the scores of estimations, random forest using pressure differences as feature variables provided the best estimation (the training score of 0.979 and the test score of 0.789). Since it was learned independently of the grids and locations, this model is expected to be generalized. It was also found that estimation is possible to some extent, even for different heat source conditions. This study is a successful demonstration of the first step in achieving the goal of new data-driven geothermal reservoir engineering, which will be developed and enhanced with the knowledge of information science.
In this study, the nominal tensile strength, Young's modulus and Weibull scale and shape parameter of the nominal tensile strength distribution of the MWCNTs synthesized by a thermal chemical vapor deposition (CVD) method were investigated by conducting uniaxial tensile tests. In addition, the structural defects which induced the failure of the MWCNTs were observed by a transmission electron microscope (TEM). TEM observations revealed that the MWCNTs exhibited several types of structural defects: discontinuous flaws such as holes, kinks and bends and remnant catalysts even though crystalline graphene layers were aligned with the MWCNT axis. The nanotube tested in this study fractured at the structural defects such as discontinuous flaws and kinks and bends, suggesting that the tensile strength of the CVD-grown MWCNTs used in this study was dominated by the above-mentioned structural defects. The tensile-loading experiments demonstrated that the nominal tensile strength, Young's modulus and Weibull scale and shape parameter of the as-grown MWCNTs were 5.2 ± 2.1 GPa, 210 ± 150 GPa, 5.9 GPa and 2.7, respectively. The MWCNTs used in this study showed larger Weibull scale parameter values compared with both the CVD-grown and arc-discharge-grown MWCNTs evaluated an earlier study. This suggested that there was an optimal nanotube structure for increasing nominal tensile strength; not too weak but also not too strong inter-tube coupling to permit an adequate load transfer between the nanotube walls and thus a consequent clean break fracture. We also investigated the effects of the thermal annealing on the mechanical properties of the MWCNTs. The structural changes observed after annealing led to no significant impact on the nominal tensile strength of the MWCNTs, which was mainly due to incomplete removal of the structural defects by thermal annealing.
Reinjection is crucial for sustainable geothermal developments. In order to predict thermal performances due to cold-water injection, a method was developed to estimate effective fracture surface areas (i.e., heat transfer areas). Tracer response curves at production wells are analyzed to determine flow rates and pore volumes, and the fracture surface areas are optimized by short-term thermal response curves. Because the method erases fracture apertures from the equation by combining mass and heat transfer equations, the fracture surfaces can be analyzed without assuming that the fracture shape is a parallel plate. The estimation method was applied to two geothermal field datasets: One involved an artificially created reservoir, and the other involved a naturally occurring reservoir. The estimated heat transfer areas are reasonable in the field geometries. Once the fracture surface area is estimated, the future temperature change and power generation can be predicted. This can provide a simple and quick method to design reinjection strategies.
Deep geological repositories for nuclear wastes consist of both engineered and natural geologic barriers to isolate the radioactive material from the human environment. Inappropriate repositories of nuclear waste would cause severe contamination to nearby aquifers. In this complex environment, mass transport of radioactive contaminants displays anomalous behaviors and often produces power-law tails in breakthrough curves due to spatial heterogeneities in fractured rocks, velocity dispersion, adsorption, and decay of contaminants, which requires more sophisticated models beyond the typical advection-dispersion equation. In this paper, accounting for the mass exchange between a fracture and a porous matrix of complex geometry, the universal equation of mass transport within a fracture is derived. This equation represents the generalization of the previously used models and accounts for anomalous mass exchange between a fracture and porous blocks through the introduction of the integral term of convolution type and fractional derivatives. This equation can be applied for the variety of processes taking place in the complex fractured porous medium, including the transport of radioactive elements. The Laplace transform method was used to obtain the solution of the fractional diffusion equation with a time-dependent source of radioactive contaminant.
1 January 2018 in Transactions of the JSME (in Japanese)