Michael Johnson

Dr. Michael Johnson

University of Nottingham
orcid

Research Focus & Metrics

Academic Career Length

35Years (1992-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 February 2006 in Polymer Composites
Verified
Journal Article
Closed access
PDF file
AEA. Endruweit
A. Endruweit
Michael JohnsonMichael Johnson
Michael Johnson
ALA. C. Long
A. C. Long

1 September 2006 in Composites Science and Technology
Verified
Journal Article
Closed access
AEA Endruweit
A Endruweit
PMP Mcgregor
P Mcgregor
ALA Long
A Long
Michael JohnsonMichael Johnson
Michael Johnson

1 May 2007 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Closed access
DMDhiren Modi
Dhiren Modi
NCNuno Curado-Correia
Nuno Curado-Correia
Michael JohnsonMichael Johnson
Michael Johnson
ALAndrew Long
Andrew Long
CRChristopher Rudd
Christopher Rudd
FRFrancois Robitaille
Francois Robitaille

1 January 2015 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Closed access
KJK. Johanson
K. Johanson
LHL.T. Harper
L.T. Harper
Michael JohnsonMichael Johnson
Michael Johnson
NWN.A. Warrior
N.A. Warrior

19 May 2016 in Journal of Materials Science
Verified
Journal Article
Open access
PDF file
DBD. T. Burn
D. T. Burn
LHL. T. Harper
L. T. Harper
Michael JohnsonMichael Johnson
Michael Johnson
NWN. A. Warrior
N. A. Warrior
UNU. Nagel
U. Nagel
JTJames Thomason
James Thomason
The objective of this study was to investigate the feasibility of combining discontinuous recycled carbon fibres with polypropylene, to produce a low-cost, high specific stiffness material for high-volume applications. The inherent low affinity of carbon fibre and polypropylene motivated a detailed study of the surface characteristics of carbon fibre and interfacial behaviour between the two materials, using the microbond test. The effects of removing the sizing from the fibres, as well as introducing a maleic anhydride-grafted polypropylene coupling agent, were extensively investigated. Polypropylene was found to degrade when prepared under atmospheric conditions; therefore, it was necessary to form droplets under nitrogen. Removal of the sizing from the fibre using pyrolysis and solvolysis techniques altered the surface morphology of the fibre and increased the interfacial shear strength (IFSS) by 4 and 33 %, respectively. A more significant improvement in the fibre–matrix adhesion was achieved by adding a maleic anhydride coupling agent at 2 wt%, which increased the IFSS by 320 %.

10 March 2014 in Journal of Composite Materials
Verified
Journal Article
Closed access
PCPh Chan
Ph Chan
Kim Yeow TshaiKim Yeow Tshai
Kim Yeow Tshai
Michael JohnsonMichael Johnson
Michael Johnson
HCHl Choo
Hl Choo
SLS Li
S Li
KZK Zakaria
K Zakaria
Oil and gas pipelines are susceptible to various forms of damage where repair mechanisms have since been developed for rehabilitation. Once installed, structural health monitoring often incurs excessive costs and defects rectification of the repaired pipeline becomes a major challenge. Finite element analysis (FEA) provides a rapid route to predict the behaviour of the rehabilitated pipelines under prescribed in-service conditions. In this paper, burst strength of a commercially available composite sleeve repair system, Helicoid Epoxy Sleeve (HES)™, which combines the use of carbon fibre strip and epoxy grout as reinforcement to damaged pipe, was investigated through experimental and numerical approaches. Design standards for subsea pipelines are used in the calculation of design pressure and burst pressure. In the experimental setup, API 5L X52 steel pipe was machined with 50% metal loss defect in wall thickness to simulate external corrosion. Results from design calculations, experimental and FEA showed good correlation with margin less than 10%.