Defects in photovoltaic panels can reduce the effective working area, and decrease the performance of the photovoltaic panels. Therefore, it is significant to identify such defects and to feed the fault information up to the production chain. Active infrared thermographic non-destructive testing has the advantages of non-contact, fast speed and large imaging area, and has been widely used in the detection of defects in various materials. In this paper, a stepped thermography of the defects, which result in degradation of energy conversion efficiency of cells in photovoltaic panels, was proposed. The front surface of the photovoltaic panel was optically stimulated by halogen lamps in step heating way, while an infrared camera was employed to monitor the temperature evolution of the front surface and to capture infrared image sequences. The thermal image sequences were processed using data processing algorithms, focusing on enhancing the defect signatures. The techniques of background subtraction, discrete Fourier transform, polynomial fitting, first-order derivative, cross correlation coefficient and histogram equalization were mainly used. Compared to the raw thermal images, the reconstructed images using suitable algorithms are more helpful to evaluate the defects. The results show that the optical stepped thermography combined with suitable post data processing is a fast and effective technique to identify the defects in photovoltaic panels.
Ultrasonic infrared thermography, thanks to its defect selective, dark-field damage detection capability, is a powerful tool for the inspection of cracks, but the ultrasound coupling is difficult for thin-walled or low-rigidity specimens if an external stimulation is employed, and the crack signature is poor for metals with high thermal conductivities. In order to detect cracks in friction stir welded joints of aluminium alloy thin plates, the constraint-excitation schemes and post image processing methods were investigated. A base excitation combined with unsymmetrical constraint condition of the thin plate were proposed and analyzed by using experiment and vibration modal analysis; a wavelet image enhancement based on symlets or biorthogonal wavelets was presented. The base excitation skill with unsymmetrical support condition and the post image processing with wavelet image enhancement were high-lighted. The results showed that the new constraint-excitation scheme was a feasible approach to detect kissing cracks in friction stir welded joints of thin plates; the wavelet image enhancement method was effective. The presented measures can greatly improve the detectability of ultrasonic thermography for thin plates.
Solder joints of printed circuit board provide the electrical and mechanical connections between electronic component and substrate. A pseudo solder inside the solder joint can reduce its electrical conductivity and often leads to crack initiation and propagation in service. The pseudo solder is a threat to the normal operation of the whole electronic equipment, especially in aerospace crafts. The pseudo solder inside the solder joint is hard to be detected with traditional electrometric method or automated optical inspection. In this paper, a laser pulse stimulated infrared thermography technique is presented to detect and identify the pseudo solder in solder joints. Characteristic parameters of the solder joints were extracted using pulsed phase thermography, temperature change rate, apparent thermal effusivity and higher-order statistics. Two neural network (NN) models based on the input patterns of data were constructed to classify the solder joints. The inputs were composed of seven characteristic parameters obtained or excess temperature evolutions. The NN was trained with the method of batch gradient descent or stochastic gradient descent. The application of principal component analysis (PCA) in data preprocessing and feature extraction was explored. Finally, the optimal scheme for pseudo solder detection with higher recognition rate was discovered. The optimal scheme is that, using PCA to extract the features from the excess temperature evolutions, and then using the stochastic gradient descent to train the neural network. The recognition rate of the sound and pseudo states can reach 95%, while the accuracy of the defective degree classification is approximately 76%.
12 June 2020 in Quantitative InfraRed Thermography Journal
Ultrasound excited vibro-thermography is based on the local heat generation due to the friction between the opposite surfaces of the defect, the plastic deformation around the defect, and/or the viscoelastic loss. This paper presents vibro-thermography applied to hybrid plates containing viscoelastic material when the viscoelastic heat generation mechanism alone is considered. The debonding-like calibrated defects without friction surfaces in the hybrid plate are detected. The dynamic temperature field is obtained by both experiment and numerical simulation. The influence of excitation frequency on the temperature increase over the defects is analysed by modelling the thermo-mechanical coupled field. The results show that the viscoelastic loss of the non-metal material is the leading factor of the local temperature increase over defects; an excitation frequency has its selective heating character to defects; a defect has a so-called defect characteristic frequency which can act as the optimal excitation frequency for this defect to be detected; the defect characteristic frequency is between the two local defect resonance frequencies corresponding to the simply supported boundary and the clamped boundary, respectively.
29 May 2015 in Quantitative InfraRed Thermography Journal
Ultrasound-excited vibrothermography (VT) is a newly developed version of InfraRed (IR) thermographic Non-Destructive Testing (NDT), but the relation between the defect signal and mechanical parameters is fuzzy due to the complexity of thermo-mechanical coupling and the interaction effects of multiple factors, so the design of operation conditions of VT is highly-dependent on the experience of operators. In order to reveal the relations of the defect signal vs. the mechanical parameters, and to enable the optimisation of operation conditions, a mathematical model was presented to simulate the heat generation and heat transfer that occur during VT. The heat power produced in a crack and the temperature increase at the crack area were solved by an analytical approach. The function of the temperature increase at the crack area vs. the mechanical parameters including the damp, mass, stiffness, amplitude and frequency of the stimulation force, friction coefficient and normal force in crack faces, excitation duration, etc., was deduced. The dependencies of temperature signals on parameters of a material and ultrasonic stimulation were theoretically analysed. The crack signature on an aluminium sample was imaged by an IR camera and compared with the theoretical predictions. The effects of experimental factors including the support condition, excitation frequency, duration and power, etc., on the crack signature were partially compared. The results show that the theoretical predictions are in agreement with the observed responses, and the influences of various mechanical parameters on VT can be quantitatively described by the analytical model presented.