Chenheng Yuan

Dr. Chenheng Yuan


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 December 2015 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
Verified
Journal Article
Closed access
PDF file
CYChenheng Yuan
Chenheng Yuan
HFHuihua Feng
Huihua Feng
YHYituan He
Yituan He
JXJing Xu
Jing Xu
The purpose of this article is to investigate the motion characteristics and dynamic mechanisms of a resonance starting process in a free-piston engine generator. A nonlinear dynamic model of the resonance starting process is described, and extensive simulation results are presented, giving insight into the engine starting characteristics; the dynamic mechanism of the resonance staring process is also studied based on a reasonable analytical method for the dynamic mode. The research results indicate that the free-piston engine generator is a single degree of freedom self-excited dynamic system with variable damping and stiffness. The starting process has oscillation stability; the piston motion can be resonated first to large stroke length by a linear motor with low electromagnetic force and then tends to reach a stable state after a few cycles in the starting process. The final amplitude is determined by the energy balance between the motor thrust force and the friction load.

12 December 2016 in International Journal of Engine Research
Verified
Journal Article
Closed access
CYChenheng Yuan
Chenheng Yuan
JXJing Xu
Jing Xu
HFHuihua Feng
Huihua Feng
YHYituan He
Yituan He
Free-piston engine generator is a new alternative to traditional reciprocating engine, which moves without mechanical restriction of crankshaft system. This article investigated numerically the friction characteristics of piston rings in a free-piston diesel engine generator by adopting coupled models of dynamic and friction. The development of the dynamic model and friction model was described, and an iterative calculation method was presented, giving insight into the coupled parameters of these two models. The detailed effects of the dynamic on friction and lubrication were investigated compared with a corresponding traditional crank engine. The friction characteristics of the free-piston engine generator were found to differ clearly from those of the traditional engine due to its special piston motion. Compared with the traditional engine, the minimum lubricant film thickness of piston rings in the free-piston engine generator is thicker and lasts shorter at the dead center regions, but it is generally thinner at other positions. The average friction force, friction power, and friction work of the piston rings in the free-piston engine generator are less than the traditional engine due to the better lubrication in endpoints region. Meanwhile, the friction power of the free-piston engine generator increases with the increase in fuel mass or decrease in load. The friction efficiency varies in correlation with the generator load; the optimum friction efficiency can be obtained by either increasing or decreasing from a certain generator load.

28 June 2017 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
Verified
Journal Article
Closed access
CYChenheng Yuan
Chenheng Yuan
JXJing Xu
Jing Xu
HFHuihua Feng
Huihua Feng
The free-piston engine generator is an attractive alternative to the conventional reciprocating engine due to the feature that it moves without crankshaft system. This paper presented a simulation for the investigation on the characteristic of in-cylinder gas motion and heat transfer in a compression ignited free-piston engine generator. An operation experiment was performed to obtain the precise piston motion for the modeling of heat transfer and gas flow. The development of the multi-dimensional model was described, and simulation results were presented and showed good similarity with the experimental data. Then, the heat transfer and gas motion in the free-piston engine generator were discussed, on which the influences of piston motion were also investigated compared with a corresponding conventional reciprocating engine. The results indicated that compared with the conventional reciprocating engine, a higher level of squish and reverse squish effect was found for the free-piston engine generator due to its faster motion around top dead center, while its slower piston motion led to weaker gas turbulence in the compression process. Moreover, the free-piston engine generator and conventional reciprocating engine did not show a significant difference in heat transfer during the compression process, however, an obvious advantage of heat transfer was indicated for the free-piston engine generator in combustion and expansion processes due to its lower combustion temperature and the reduced time that is available for heat transfer caused by its faster expansion. The mechanism for such differences is that the free-piston engine generator moves with uneven equivalent speed.

17 May 2018 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
CHCuijie Han
Cuijie Han
CYChenheng Yuan
Chenheng Yuan
YHYituan He
Yituan He
YLYang Liu
Yang Liu
The free-piston engine generator is a new power machinery, which removes the crank-shaft mechanism. This article aims to study the impact of different injection rate shapes (left triangle, rectangle, and right triangle) on the free-piston engine generator spray and combustion characteristics. An iteration numerical model was established and validated by experiment. The results reveal that there is a positive correlation between injection rate and evaporation rate, and the faster evaporation rate is more conducive to total evaporated fuel mass. The left triangle and rectangle injection modes have the better level of atomization and mixing in the early injection due to stronger turbulent kinetic energy, longer penetration, and smaller Sauter mean diameter, while the right triangle has opposite results, which impairs the mixture formation, and its higher injection pressure in the late injection duration causes more impinged fuel mass. Moreover, the temperature, pressure, peak heat release rate, and indicated thermal efficiency for the left triangle are greater than the other two injection modes. Therefore, for the free-piston engine generator, faster injection rate in the early injection stage enables to improve the fuel evaporation, atomization, and mixing processes, meanwhile enhances the level of isochoric heat release around top dead center, resulting in higher indicated thermal efficiency.

2 June 2017 in International Journal of Engine Research
Verified
Journal Article
Closed access
CYChenheng Yuan
Chenheng Yuan
JXJing Xu
Jing Xu
YHYituan He
Yituan He
The free-piston engine alternator is a new crankless engine. The traditional starting method cannot be used to conveniently initialize the new engine. This article introduced a resonance starting method and investigated the effects of influential parameters on the free-piston engine alternator starting. An experimental free-piston engine alternator prototype was developed, and the effects of starting force, connecting rod length, and piston assembly mass on the resonance starting were experimented. Experimental results show that the piston motion is influenced by the starting force, and the final compression ratio of the engine is increased with the enlarged thrust force. A more high starting compression ratio can be obtained by either increasing or decreasing from the certain translator mass. The experiment also suggests that properly enlarging the connecting rod length can enhance the starting capacity of a linear alternator with a constant force. Moreover, an advanced simulation model was presented for the parametric study of the starting process. The effects of heat transfer, friction, and leakage on the resonance starting were investigated. Simulation indicates that the heat transfer is a significant inference on free-piston engine alternator starting, and the peak gas pressure varies in negative correlation with the piston ring closed clearance and friction load. As a result, the starting control strategy of free-piston engine alternator is required to consider these influential parameters.

13 September 2017 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
JXJing Xu
Jing Xu
CYChenheng Yuan
Chenheng Yuan
YHYituan He
Yituan He
RWRong Wang
Rong Wang
The free-piston engine generator has been a research focus lately due to its crankless structure and unconstrained piston motion, which brings about some weaknesses for the combustion process. This study aims to explore the optimization possibility of combustion using its free-piston motion. Three potential piston motion trajectories were obtained by the free-piston engine generator dynamic model and then served as the boundary condition to establish the combustion model. Through the simulations and comparisons of combustion processes in different piston motions, a manner to optimize the free-piston engine generator combustion performance, that is, by adjusting the piston motion trajectory, was proposed and verified effectively. The results show that under the situation of the slowest velocity and smallest acceleration around the top dead center, the piston moves with a smallest change in in-cylinder gas volume but greatest heat release around the top dead center, during which the free-piston engine generator gains the greatest peak values of in-cylinder pressure, temperature, and the rate of heat release and pressure rise in the three, naturally leading to the highest NO emission and soot emission; the late combustion duration and heat released in the late combustion are smaller than the other two cases. But the fastest piston motion around the top dead center shortens the duration of combustion and heat release and brings about greater soot emission than the case of conventional sinusoidal trajectory.