Du xin Li

Prof. Du xin Li


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 March 2020 in Polymer Bulletin
Verified
Journal Article
Closed access
PDF file
CXChunguang Xiao
Chunguang Xiao
DLDu xin Li
Du xin Li
DZDan Zeng
Dan Zeng
FLFeng Lang
Feng Lang
YXYu Xiang
Yu Xiang
YLYi Lin
Yi Lin

12 June 2019 in Plastics, Rubber and Composites: Macromolecular Engineering
Verified
Journal Article
Closed access
DLDu xin Li
Du xin Li
DZDan Zeng
Dan Zeng
QCQian Chen
Qian Chen
MWMengling Wei
Mengling Wei
LSLing Song
Ling Song
DPDonghua Pan
Donghua Pan
Nylon 6 (PA6) thermal conductive composites were prepared by melt blending with different sizes of spherical Al2O3 and AlN and the filling amount was 60 wt%. This paper explored the effects of different particle sizes and filler kinds on the thermal conductivity and mechanical properties of the composites. The results showed that the composites filled with AlN and spherical Al2O3 had higher thermal conductivity than the composites filled with single filler under the same filling amount. When the mass ratio of 48 μm spherical Al2O3 and 14 μm AlN was 1:2, the thermal conductivity and thermal diffusivity was 2.44 W/(m·K) and 0.72 mm2/s, respectively. In addition,the tensile strength was 57.50 MPa and the impact strength was 6.13 KJ/m2. By comparing actual thermal conductivity value with the theoretical value calculated by Agari model, we found that actual value of alumina filling was close to the theoretical value.

18 November 2015 in Polymer Composites
Verified
Journal Article
Closed access
PDF file
DLDu xin Li
Du xin Li
RLRuoyun Lv
Ruoyun Lv
GSGaojie Si
Gaojie Si
YYYilan You
Yilan You

28 November 2019 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
LSLing Song
Ling Song
HYHaiyang Yang
Haiyang Yang
DLDu xin Li
Du xin Li
QJQibin Jiang
Qibin Jiang
DZDan Zeng
Dan Zeng

16 March 2015 in Polymer Composites
Verified
Journal Article
Closed access
PDF file
QZQi Zhang
Qi Zhang
DLDu xin Li
Du xin Li
DLDengwang Lai
Dengwang Lai
YYYilan You
Yilan You
BOBaoli Ou
Baoli Ou

25 May 2017 in High Performance Polymers
Verified
Journal Article
Closed access
DLDu xin Li
Du xin Li
XHXi Hu
Xi Hu
ZHZihua Huang
Zihua Huang
YCYue Chen
Yue Chen
HHHao Han
Hao Han
CXChunguang Xiao
Chunguang Xiao
The N-polyamide 6 (N-PA6) was used as a toughening agent to improve the mechanical properties of a thermosetting phenol formaldehyde (PF) resin. Then, molybdenum disulfide (MoS2) and graphite (Gr) were added as friction modifiers to improve the tribological properties of PF resin–N-PA6 composite. In this article, it was found that PF resin with 2 wt% N-PA6 has the best performance in tensile strength (41.9 MPa) and notched Izod impact strength (3.7 kJ/m2). When MoS2 or Gr was added, tensile strength was reduced, while notched Izod impact strength increased at first and then decreased. Wear testing showed that PF resin filled by 2 wt% N-PA6 possessed both low friction coefficient (0.3794) and wear rate (7.88×10−5 mm3/Nm). MoS2 or Gr could be added to further reduce the wear rate and make the friction coefficient more stable. Scanning electron microscope test showed that N-PA6 provides a smoother friction surface.