Cong-Truong Dinh

Dr. Cong-Truong Dinh

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2021 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
CDCong-Truong Dinh
Cong-Truong Dinh
TNT. M. Nguyen
T. M. Nguyen
TVT. D. Vu
T. D. Vu
SPS. G. Park
S. G. Park
QNQ. H. Nguyen
Q. H. Nguyen
Due to the great heat obtained from the combustion chamber, the turbine blades of a jet engine always operate at high temperatures. Therefore, to minimize the temperature of the turbine rotor and stator blades, the internal cooling system was developed. The original rib called the squared-rib has been developed as a turbulence generator to enhance heat transfer ability. This technique is to cast ribs in the serpentine passage inside the turbine blades. By this technique, the vortex exists in the rear rib region that causes a low heat transfer zone. In this investigation, a new rib configuration called the truncated-root rib was designed to reduce the squared-rib disadvantage. The configuration of the truncated-root rib forms a small extra-passage into which the coolant passes through and the vortex is comparatively removed. To investigate the heat transfer performance and fluid flow characteristic of the internal cooling turbine blades, a parametric study of the truncated-root rib with the height and shapes of the extra-passage was performed using three-dimensional Reynolds-averaged Navier–Stokes equations with the shear stress transport turbulence model. The numerical results showed that all the heat transfer performance of the truncated-root rib configuration is greater than that of the squared-rib. The Nusselt number in the case of the truncated-root rib increases by 8.56% with the Reynolds number of 37 392, and the thermal performance is 39.24% higher than that of the original shape in the case with Reynolds number 53 697.

1 April 2021 in Aerospace Science and Technology
Verified
Journal Article
Closed access
TVTien Dung Vuong
Tien Dung Vuong
Kwang-Yong KimKwang-Yong Kim
Kwang-Yong Kim
CDCong-Truong Dinh
Cong-Truong Dinh

19 June 2022 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
KDKhanh-Duy Cong Do
Khanh-Duy Cong Do
DCDuy-Hung Chung
Duy-Hung Chung
DTDang-Quoc Tran
Dang-Quoc Tran
CDCong-Truong Dinh
Cong-Truong Dinh
QNQuang-Hai Nguyen
Quang-Hai Nguyen
KKKwang-Yong Kim
Kwang-Yong Kim

17 October 2022 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
MKMin Sik Kang
Min Sik Kang
SPSung Goon Park
Sung Goon Park
CDCong-Truong Dinh
Cong-Truong Dinh

1 March 2020 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
HPHien Phan
Hien Phan
PDPenghao Duan
Penghao Duan
CDCong-Truong Dinh
Cong-Truong Dinh
Accurate predictability of high-pressure turbine nozzle guide vane aero-thermal performance is highly desired in the development campaign due to the exposure of the component to a frequent and high heat load. In this paper, the representative vane profile in modern aero-engines is numerically studied. Aerodynamics and aero-thermal validations of the blade profile have been performed in comparison with the available experimental data. It has been shown that a satisfactory agreement could be achieved with the use of the transitional turbulence model shear stress transport γ–θ due to its superiority in capturing the laminar–turbulent transition. Sensitivity studies on the increase in the inlet turbulence intensity, inlet endwall boundary layer thickness, and inlet total temperature profile have been performed to understand the impact of inflow conditions’ uncertainty on the aero-thermal predictability. Increasing the inlet turbulence intensity increases the pressure surface heat transfer coefficient and induces an earlier transition onset on the suction surface. Due to the rapid decay of turbulence intensity in the numerical model, the use of an artificially high inlet turbulence intensity has been shown to be effective in the prediction improvement. On the other hand, the change in the inlet boundary layer thickness influences the formation and strength of the secondary flow, namely, horseshoe vortex and passage vortex. These secondary flow phenomena affect the local blade surface heat transfer coefficient in the near-endwall region although the most significant rise in heat transfer is found on the endwall. The temperature distortion amplitude of a hot streak and its relative clocking position with the vane significantly affect the heat flux distribution. In contrast, the heat transfer coefficient is less sensitive to the change in hot streak conditions. However, it has been shown that increasing the temperature distortion amplitude could induce a larger difference among different clocking configurations. In addition, decreasing the difference between the fluid and wall temperature would delay the transition onset and stabilize the boundary layer. Further analysis of the unsteady effects has been carried out by comparing the steady and time-averaged flow solutions. It has been observed that the discrepancy between these solutions is attributed to the flow field nonlinearity. Thus, a significant discrepancy can be found in the laminar–turbulent transition as well as in the trailing edge region. However, since the contribution of these regions on the total area-averaged heat transfer is small, their influence on the total vane heat transfer is limited.

20 December 2019 in International Journal of Aeronautical and Space Sciences
Verified
Journal Article
Closed access
PDF file
CDCong-Truong Dinh
Cong-Truong Dinh
DVDinh-Quy Vu
Dinh-Quy Vu
Kwang-Yong KimKwang-Yong Kim
Kwang-Yong Kim