Understanding the electronic contact between molybdenum disulfide (MoS2) and metal electrodes is vital for the realization of future MoS2-based electronic devices. Natural MoS2 suffers from a high density of both metal and sulfur defects and impurities. We present evidence that subsurface metal-like defects with a density of ∼1011 cm-2 induce a negative ionization of the outermost S atom complex. We investigate with high spatial resolution surface characterization techniques the effect of these defects on the local conductance of MoS2. By using metal nanocontacts (contact area <6 nm2), we find that subsurface metal-like defects (and not S-vacancies) drastically decrease the metal/MoS2Schottky barrier height as compared to pristine regions. The magnitude of this decrease depends on the contact metal. The decrease of the Schottky barrier height is attributed to strong Fermi level pinning at the defects. Indeed this is demonstrated in the measured pinning factor which is equal to ∽0.1 at defect locations and ∽0.3 at pristine regions. Our findings are in good agreement with the theoretically predicted values. These defects provide low resistance conduction paths in MoS2-based nanodevices and will play a prominent role as the device junction contact area decreases in size.
14 February 2019 in The Journal of Physical Chemistry C
Understanding the electron transport through transition metal dichalcogenides (TMDCs) based semiconductor/metal junctions is vital for the realization of future TMDC based (opto-)electronic devices. Despite the bonding in TMDCs being largely constrained within the layers, strong Fermi level pinning was observed in TMDC based devices, reducing the tunability of the Schottky barrier height. We present evidence that metal induced gap states (MIGS) are the origin for the large Fermi level pinning similar to conventional semiconductors. A variety of TMDCs (MoSe2, WSe2, WS2 and MoTe2) were investigated using high-spatial resolution surface characterization techniques, permitting us to distinguish between defected and pristine regions. The Schottky barrier heights on the pristine regions can be explained by MIGS, inducing partial Fermi level pinning. The Fermi level pinning strength is further enhanced by disorder induced gap states (DIGS) induced by transition metal vacancies or substitutionals at the defected regions. Our findings emphasize the importance of defects on the electron transport properties in TMDC based devices and confirm the origin of Fermi level pinning in TMDC based metal/semiconductor junctions.
9 April 2020 in Angewandte Chemie International Edition
We studied the energy-level alignment at interfaces between various transition-metal dichalcogenide (TMD) monolayers, MoS2, MoSe2, WS2, and WSe2, and metal electrodes with different work functions (WFs). TMDs were deposited on SiO2/silicon wafers by chemical vapor deposition and transferred to Al and Au substrates, with significantly different WFs to identify the metal–semiconductor junction behavior: oxide-terminated Al (natural oxidation) and Au (UV–ozone oxidation) with a WF difference of 0.8 eV. Kelvin probe force microscopy was employed for this study, based on which electronic band diagrams for each case were determined. We observed the Fermi-level pinning for MoS2, while WSe2/metal junctions behaved according to the Schottky–Mott limit. WS2 and MoSe2 exhibited intermediate behavior.
The classic regelation experiment of Thomson in the 1850s deals with cutting an ice cube, followed by refreezing. The cutting was attributed to pressure-induced melting but has been challenged continuously, and only lately consensus emerged by understanding that compression shortens the O:H nonbond and lengthens the H–O bond simultaneously. This H–O elongation leads to energy loss and lowers the melting point. The hot debate survived well over 150 years, mainly due to a poorly defined heat exchange with the environment in the experiment. In our current experiment, we achieved thermal isolation from the environment and studied the fully reversible ice–liquid water transition for water confined between graphene and muscovite mica. We observe a transition from two-dimensional (2D) ice into a quasi-liquid phase by applying a pressure exerted by an atomic force microscopy tip. At room temperature, the critical pressure amounts to about 6 GPa. The transition is completely reversible: refreezing occurs when the applied pressure is lifted. The critical pressure to melt the 2D ice decreases with temperature, and we measured the phase coexistence line between 293 and 333 K. From a Clausius–Clapeyron analysis, we determine the latent heat of fusion of two-dimensional ice at 0.15 eV/molecule, being twice as large as that of bulk ice.
We have measured the two-dimensional image potential states (IPS) of a germanene layer synthesized on a Ge2Pt crystal using scanning tunnelling microscopy and spectroscopy. The IPS spectrum of germanene exhibits several differences as compared to the IPS spectrum of pristine Ge(001). First, the n = 1 peak of the Rydberg series of the IPS spectrum of germanene has two contributions, labelled n = 1- and n = 1+, respectively. The peak at the lower energy side is weaker and is associated to the mirror-symmetric state with opposite parity. The appearance of this peak indicates that the interaction between the germanene layer and the substrate is very weak. Second, the work function of germanene is about 0.75 eV lower in energy than the work function of Ge(001). This large difference in work function of germanene and pristine Ge(001) is in agreement with first-principles calculations.