Petawatt lasers are now available in a number of facilities around the world and are becoming a very useful tool in physics and engineering. Some of such lasers are able -or will be able soon- to fire at high repetition rates (one shot per second or more). Experiments at such repetition rates have certain peculiarities that are to be briefly exposed here, based on the author’s experience with the Salamanca VEGA-3 laser. VEGA-3 is a 30 fs PW laser, firing one shot per second.
We present a technique to assess the focal volume of petawatt-class lasers at full power. Our approach exploits quantitative measurement of the angular distribution of electrons born in the focus via ionization of rarefied gas, which are accelerated forward and ejected ponderomotively by the field. We show that a bivariate () angular distribution, which was obtained with image plates, not only enables the peak intensity to be extracted, but also reflects nonideality of the focal-spot intensity distribution. In our prototype demonstration at intensities of a few to a few , an f/10 optic produced a focal spot in the paraxial regime. This allows a plane-wave parametrization of the peak intensity given by ( being the normalized vector potential and the minimum ejection angle) to be compared with our measurements. Qualitative agreement was found using an inferred from the pulse energy, pulse duration, and focal spot distribution with a modified parametrization, (). This highlights the need for (i) better understanding of intensity degradation due to focal-spot distortions and (ii) more robust modeling of the ejection dynamics. Using single-shot detection of electrons, we showed that while there is significant shot-to-shot variation in the number of electrons ejected at a given angular position, the average distribution scales with the pulse energy in a way that is consistent with that seen with the image plates. Finally, we note that the asymptotic behavior as limits the usability of angular measurement. For 800 nm, this limit is at an intensity .
Spatial distributions of electrons ionized and scattered from ultra-low-pressure gases are proposed and experimentally demonstrated as a method to directly measure the intensity of an ultra-high-intensity laser pulse. Analytic models relating the peak scattered electron energy to the peak laser intensity are derived and compared to paraxial Runge–Kutta simulations highlighting two models suitable for describing electrons scattered from weakly paraxial beams (f#>5) for intensities in the range of 1018−1021 W cm−2. Scattering energies are shown to be dependent on gas species, emphasizing the need for specific gases for given intensity ranges. Direct measurements of the laser intensity at full power of two laser systems are demonstrated, both showing a good agreement between indirect methods of intensity measurement and the proposed method. One experiment exhibited the role of spatial aberrations in the scattered electron distribution, motivating a qualitative study on the effect. We propose the use of convolutional neural networks as a method for extracting quantitative information on the spatial structure of the laser at full power. We believe the presented technique to be a powerful tool that can be immediately implemented in many high-power laser facilities worldwide.
In this paper we will show that photon–photon collision experiments using extreme lasers can provide measurable effects giving fundamental information about the essence of QED, its Lagrangian. A possible scenario with two counterpropagating ultra-intense lasers for an experiment to detect scattering between optical photons is analyzed. We discuss the importance of the pulse widths and waists, the best scenario for overlapping the beams and signal detection, as well as ways to distinguish the signal from the noise. This would need a high-precision measurement, with control of temporal jitter and noise. We conclude that such experiment is barely feasible at 1023 W cm−2 and very promising at 1024 W cm−2.
The classical nonlinear incoherent Thomson Scattering (TS) power spectrum from free relativistic electrons moving in a laser beam with orbital angular momentum (OAM) is investigated. The main focus in this paper is on the TS process as a diagnostic technique for this type of beams. Linearly polarized incoming radiation and electrons of very low initial kinetic energy are considered. Averaged spectra from electrons randomly covering the transverse laser pattern have different shape in the case of a beam with OAM as compared with the TEM00 case (with vanishing net OAM). Hence, spectrally resolved measurements are needed to discriminate between both cases. If electrons are distributed over the laser spot as thin stripes at a given angle with respect to the polarization direction, computations show non-trivial angular dependencies of integrated power of a laser with OAM as compared with the TEM00 mode. An experimental test of the OAM state of a laser beam is proposed based on these results. The numerical code developed is general enough to deal with more complex polarization states of the laser beam and/or electrons having arbitrary initial kinetic energies.
For high repetition ultrahigh-intensity laser system, automatic alignment of structured target is key to achieving consistent particle acceleration and plasma heating. In this work, we demonstrate efficient electron acceleration with two sequential steps of laser processing using a high repetition rate, 30-fs ultrahigh-intensity laser. The first pulse does laser machining and creates a steep cylindrical crater on the surface of a flat stainless-steel target. The crater is formed by the hydrodynamic expansion of the heated surface and by spallation of the inner, deeper material by nonthermal relativistic electrons. The crater shape is well controlled and reproducible with 200 μm width and 350 μm depth. The second pulse irradiates deeply inside the crater and interacts with the crater wall, efficiently accelerating electrons via surface plasmonic, without need for target realignment. The laser absorption efficiency increases from 32.5 to 97.5% by the process.