Wenhua Li

Dr. Wenhua Li

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 May 2021 in Rare Metals
Verified
Journal Article
Closed access
PDF file
SLSong Li
Song Li
YCYong‐Li Cao
Yong‐Li Cao
WLWenhua Li
Wenhua Li
ZBZhi‐Shan Bo
Zhi‐Shan Bo

17 May 2019 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
LZLiren Zhang
Liren Zhang
JWJionghua Wu
Jionghua Wu
DLDongmei Li
Dongmei Li
WLWenhua Li
Wenhua Li
QMQingbo Meng
Qingbo Meng
ZBZhishan Bo
Zhishan Bo
The intramolecular S–O interaction was first adopted for designing conjugated polymer HTMs in perovskites solar cells. It could lock the flat conformation of polymer backbones, which enabled the polymer molecules to pack closely in the solid state, facilitating hole transportation. The solubility of the conjugated polymers could be improved by introducing alkyloxy side chains, whereas their planarity in the solid state was not affected. Furthermore, high hole mobility of 1.72 × 10−3 cm2 V−1 s−1 and a suitable HOMO energy level of −5.43 eV could be achieved by side chain engineering. Finally, PCE of 18.30% was obtained for P1-based dopant-free devices, which most importantly showed much better long-term ambient stability than those based on traditional spiro-MeOTAD.

28 October 2015 in Chemical Communications
Verified
Journal Article
Closed access
PDF file
JZJicheng Zhang
Jicheng Zhang
XZXuejuan Zhang
Xuejuan Zhang
GLGuangwu Li
Guangwu Li
HXHongmei Xiao
Hongmei Xiao
WLWenhua Li
Wenhua Li
ZBZhishan Bo
Zhishan Bo
A small molecular acceptor was synthesized for wide band gap polymer based nonfullerene OPVs to achieve a PCE of 3.71%, which is the best value for nonfullerene OPVs with a Voc higher than 1 V.

23 January 2019 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
YZYun Zhang
Yun Zhang
CKChun Kou
Chun Kou
JZJunjie Zhang
Junjie Zhang
YLYahui Liu
Yahui Liu
WLWenhua Li
Wenhua Li
MSMing Shao
Ming Shao
The performance of p–i–n planar perovskite solar cells (PSCs) strongly depends on the electronic structure and interfacial properties of hole transporting materials (HTMs). Four diphenylamine derivatives with a fluorene core were synthesized and employed as hole transport layers in inverted p–i–n planar PSCs. HTMs that are endowed with vinyl crosslinking units can form insoluble 3D networks under mild annealing temperature, which improve the solvent resistance during the device fabrication and morphological stability. Moreover, the optimized devices incorporating crosslinked HTMs exhibit an impressive power conversion efficiency of 18.7% with a high Jsc of 20.89 mA cm−2, Voc of 1.15 V and FF of 77.8%, which are superior to those of PEDOT:PSS based PSCs. The ultraviolet photoelectron spectroscopy measurement justifies that the new HTMs feature deep HOMO levels aligning well with the perovskite. Moreover, the hydrophobic nature of the synthesized HTMs favors the formation of large grained and continuous perovskite films with good surface coverage, evidenced by the water contact angles and film morphology measurements. Steady-state and time-resolved photoluminescence studies also reveal that fast charge transfer and suppressed recombination occur between the perovskite and HTMs. Our studies demonstrate that employing crosslinked organic HTMs is a promising approach to achieve high efficiency and stable PSCs.

25 April 2016 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
YLYahui Liu
Yahui Liu
WZWenchao Zhao
Wenchao Zhao
YWYang Wu
Yang Wu
JZJicheng Zhang
Jicheng Zhang
GLGuangwu Li
Guangwu Li
ZBZhishan Bo
Zhishan Bo
Two kinds of new conjugated polymers (P1 and P2) with benzothiadiazole as the acceptor unit and thiophene as the donor unit were designed, synthesized and used as donor materials for polymer solar cells (PSCs). These polymers show a broad absorption in the visible region, a medium band gap of about 1.75 eV, and a low-lying HOMO energy level of about −5.65 eV. The open-circuit voltage (Voc) of both P1 and P2 was greatly improved to 0.85 V mainly due to the introduction of a carboxylate group at the 3-position of the thiophene spacer. Fluoro substitution on the polymer backbone of P2 can greatly enhance the interchain interaction, leading to a huge increase of short-circuit current density (Jsc). P2-based devices with the active layer spin-coated from 1,2-diclorobenzene (DCB) solutions that contain 1% 1,8-diiodooctane (DIO) and washed with methanol showed a synergistic positive effect, resulting in a significant enhancement of the power conversion efficiency (PCE) up to 8.67%. The PCE could be further improved by constructing inverted devices and the best efficiency of 9.26% was finally obtained. In addition, the mechanism for achieving such a high PCE for P2 based devices was also proposed based on the morphological analysis of the blend films by atomic force microscopy (AFM), transmission electron microscopy (TEM), grazing incident angle X-ray scattering (GIWAXS) and resonant soft X-ray scattering (RSoXS). The improvement can be ascribed to the enhanced molecular packing and proper phase separation of the blend films and the reduced charge recombination.

18 February 2016 in ACS Nano
Verified
Journal Article
Closed access
HWHuan Wang
Huan Wang
QLQian Liu
Qian Liu
WLWenhua Li
Wenhua Li
Liping WenLiping Wen
Liping Wen
DZDong Zheng
Dong Zheng
LJLei Jiang
Lei Jiang