William Hearn

Mr. William Hearn

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 May 2022 in Materialia
Verified
Journal Article
Open access
WHWilliam Hearn
William Hearn
KLKristina Lindgren
Kristina Lindgren
JPJohan Persson
Johan Persson
Eduard HryhaEduard Hryha
Eduard Hryha

17 October 2022 in Powder Metallurgy
Verified
Journal Article
Open access
WHWilliam Hearn
William Hearn
PHPeter Harlin
Peter Harlin
EHEduard Hryha
Eduard Hryha
This study focuses on process development and mechanical property evaluation of AISI 4140, 4340 and 8620 low-alloy steel produced by powder bed fusion – laser beam (PBF-LB). Process development found that increasing the build plate preheating temperature to 180°C improved processability, as it mitigated lack of fusion and cold cracking defects. Subsequent mechanical testing found that the low-alloy steels achieved a high ultimate tensile strength (4140:∼1400 MPa, 4340:∼1500 MPa, 8620:∼1100 MPa), impact toughness (4140:∼90–100 J, 4340:∼60–70 J, 8620:∼150–175 J) and elongation (4140:∼14%, 4340:∼14%, 8620:∼14–15%) that met or exceeded the ASTM standards. Mechanical testing also revealed limited directional anisotropy that was attributed to low levels of internal defects (< 0.1%), small grains with weak crystallographic texture and improved tempering due to build plate preheating and post PBF-LB stress relief. This indicates that with adequate process development, low-alloy steels produced by PBF-LB can meet or exceed the performance of conventionally produced alloys.

29 July 2021 in Powder Metallurgy
Verified
Journal Article
Open access
WHWilliam Hearn
William Hearn
RSRobert Steinlechner
Robert Steinlechner
EHEduard Hryha
Eduard Hryha
This study focuses on the processability of four low-alloy steels (AISI 4130, 4140, 4340 and 8620) via laser-based powder bed fusion (LB-PBF). In the as-built condition, the alloys consisted of tempered martensite that was the result of an intrinsic heat treatment (IHT) during LB-PBF. In terms of defects, a distinct transition in porosity was observed that correlated to the volumetric energy density (VED). At low VED, specimens contained a lack of fusion porosity, while at high VED, they contained keyhole porosity. Additionally, cold cracking was observed in 4140 and 4340 specimens produced at low/intermediate VEDs. This cracking could be mitigated by increasing the VED or laser power, as both enhance the IHT. This enhanced IHT lowered the material hardness below specific thresholds (<500HV 4340 and 99.8%) low-alloy steel specimens were produced without the requirement of build plate preheating.

27 June 2024 in Journal of Applied Crystallography
Verified
Journal Article
Open access
PDF file
MCMads Carlsen
Mads Carlsen
CAChristian Appel
Christian Appel
WHWilliam Hearn
William Hearn
MOMartina Olsson
Martina Olsson
AMAndreas Menzel
Andreas Menzel
MLMarianne Liebi
Marianne Liebi
Small-angle X-ray tensor tomography and the related wide-angle X-ray tensor tomography are X-ray imaging techniques that tomographically reconstruct the anisotropic scattering density of extended samples. In previous studies, these methods have been used to image samples where the scattering density depends slowly on the direction of scattering, typically modeling the directionality, i.e. the texture, with a spherical harmonics expansion up until order ℓ = 8 or lower. This study investigates the performance of several established algorithms from small-angle X-ray tensor tomography on samples with a faster variation as a function of scattering direction and compares their expected and achieved performance. The various algorithms are tested using wide-angle scattering data from an as-drawn steel wire with known texture to establish the viability of the tensor tomography approach for such samples and to compare the performance of existing algorithms.

3 January 2022 in Frontiers in Materials
Verified
Journal Article
Open access
WHWilliam Hearn
William Hearn
EHEduard Hryha
Eduard Hryha
The present study examines the processability of Fe-C alloys, with carbon contents up to 1.1 wt%, when using laser based powder bed fusion (LB-PBF). Analysis of specimen cross-sections revealed that lack of fusion porosity was prominent in specimens produced at low volumetric energy density (VED), while keyhole porosity was prominent in specimens produced at high VED. The formation of porosity was also influenced by the carbon content, where increasing the carbon content reduced lack of fusion porosity, while simultaneously increasing the susceptibility to form keyhole porosity. These trends were related to an improved wettability, viscosity, and flow of the melt pool as well an increased melt pool depth as the carbon content increased. Cold cracking defects were also observed in Fe-C alloys that had an as-built hardness ≥425 HV. Reducing the carbon content below 0.75 wt% and increasing the VED, which improved the intrinsic heat treatment during LB-PBF, were found to be effective mitigation strategies to avoid cold cracking defects. Based upon these results, a process window for the Fe-C system was established that produces high density (>99.8%), defect-free specimens via LB-PBF without the requirement of build plate preheating.

10 July 2025 in Virtual and Physical Prototyping
Verified
Journal Article
Open access
AÖAndaç Özsoy
Andaç Özsoy
WHWilliam Hearn
William Hearn
SGSteve Gaudez
Steve Gaudez
RJRijuta Jeswani
Rijuta Jeswani
YCYunhui Chen
Yunhui Chen
SPSteven Van Petegem
Steven Van Petegem