To produce high-quality prints using flexographic printing technology, it is important, among other factors, how accurately and consistently the ink is delivered to the printing plate, and, from there, onto the printed material. This function is performed by anilox rollers. The aim of this research is to investigate the condition of anilox rollers in printing houses in the Baltic states. The study evaluated the wear and cell clogging of anilox rollers. The dependency of clogging on the cell size, as well as the dependency of wear on the cell size (i.e., change in cell volume) and quantity of doctor blades, was investigated. In addition, the uniformity of cell clogging and wear on the surface of the anilox roller was evaluated. Studies have shown that more than half of the anilox rollers in printing houses are not washed properly; higher line screen anilox rollers tend to become more clogged, and it is important to take measurements at more than three locations to assess the reliability of more worn rollers.

The present study aims to explore the stressed state of cartilage using various meniscal tear models. To perform this research, the anatomical model of the knee joint was developed and the nonlinear mechanical properties of the cartilage and meniscus were verified. The stress–strain curve of the meniscus was obtained by testing fresh tissue specimens of the human meniscus using a compression machine. The results showed that the more deteriorated meniscus had greater stiffness, but its integrity had the greatest impact on the growth of cartilage stresses. To confirm this, cases of radial, longitudinal, and complex tears were examined. The methodology and results of the study can assist in medical diagnostics for meniscus treatment and replacement.

The growing interest in biodegradable scaffolds for bone regeneration created a need to investigate new materials suitable for scaffold formation. Poly(lactic acid) (PLA) is a polymer commonly used in biomedical engineering, e.g. in tissue engineering as a biodegradable material. However, the mechanical behavior of PLA along its degradation time is still not explored well. For this reason, the mechanical properties of PLA scaffolds affected by incubation in physiological medium needs to be investigated to show the potential of PLA to be used as a material for biodegradable scaffold formation. The purpose of this research is to determine the mechanical properties of PLA scaffolds before and after incubation, and to apply constitutive material models for further behavior prediction. Two sets of PLA scaffolds were printed by the 3D printer “Prusa i3 MK3S” and sterilized by ultraviolet light and ethanol solution. The first set of specimens was incubated in DMEM (Dulbecco’s Modified Eagle Medium) for 60, 120, and 180 days maintaining 36.5 °C temperature. The mechanical properties of the scaffolds were determined after performing the compression test in the “Mecmesin MultiTest 2.5-i” testing stand with a force applied at two different speed modes. The obtained data was curve fitted with the hyperelastic material models for a model suitability study. The second set of specimens was incubated in PBS (Phosphate Buffered Saline) for 20 weeks and used in a polymer degradation study. The obtained results show that the mechanical properties of PLA scaffolds do not decrease during incubation in physiological medium for a predicted new bone tissue formation period, though hydrolysis starts at the very beginning and increases with time. PLA as a material seems to be suitable for the use in bone tissue engineering as it allows to form biocompatible and biodegradable scaffolds with high mechanical strength, required for effective tissue formation.

One vital component in the flexo inking system of high-line screen engraving technologies is anilox rollers. These deliver a precise and consistent amount of ink during the process of flexography, making it possible to produce high-resolution prints of exceptional quality. However, as print quality continues to improve, printing houses are experiencing more frequent problems with anilox rollers, such that ink transfer during printing operations is being unpredictably reduced. Due to the lack of research into anilox rollers there is insufficient objective information on how to maintain them at peak performance and condition. This study investigates the clogging of anilox roller cells (without assessing cell wear) in a number of printing houses in the Baltic States. Cell clogging of anilox rollers was determined depending on cell size, ink type and washing method.

The aim of this research is to investigate related effect of dyeability to linen textiles related to different printing parameters. The study investigated the change in color characteristics when printing on linen fabrics with an inkjet MIMAKI Tx400-1800D printer with pigmented TP 250 inks. The dependence of color reproduction on linen fabrics on the number of print head passes, number of ink layers to be coated, linen fabric density, and different types of linen fabric was investigated. All this affects the quality of print and its mechanical properties. The change in color characteristics on different types of linen fabrics was determined experimentally. We determine at which print settings the most accurate color reproduction can be achieved on different linen fabrics. The difference between the highest and the lowest possible number of head passages was investigated. The possibilities of reproducing different linen fabric colors were determined.

In this paper examines the possibilities of applying 3D printing in the manufacture of orthoses. Features of 3D printing of biocompatible materials are analyzed. In this work, mechanical bending tests of three printed samples were performed. Based on test results, PETG material is selected for 3D modeling and printing. Technological properties of 3D printing were summarized. Modeling and printing of the orthoses prototype, compared to traditional methods, takes less time, and uses lower material costs, does not require much physical effort, is well suited to the patient’s body anatomy, and has a variety of design options.