Antoine Merlo

Mr. Antoine Merlo

Chemical Engineering, University of Liège, Liège, Wallonia, Belgium
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 July 2021 in Materials
Verified
Journal Article
Open access
PDF file
AMAntoine Merlo
Antoine Merlo
GLGrégoire Léonard
Grégoire Léonard
The coating of materials with specific films is widely used to improve material properties and many technologies exist to perform it. In the last few years, the replacement of wet electrodeposition processes has been continuously encouraged in the EU due to the problematic waste management linked to those processes. In this paper, magnetron sputtering is studied as an alternative to conventional electrodeposition by comparing the technologies’ environmental impacts and costs. From the study, it appears that while magnetron sputtering greatly reduces hexavalent chromium emissions over the production, it has an increased electricity consumption mostly due to its lower production capacity, thus leading to more greenhouse gas emissions. Furthermore, a short discussion on the quantification of the impact of hexavalent chromium emissions is conducted. Regarding costs, the electrodeposition process has a lower cost of investment and of consumables, but requires more work time for the different steps of the process, making the total price per functional unit roughly equal. However, the cost per functional unit strongly depends on assumptions on the required work time, for which a sensitivity study is performed. Finally, the impacts of these two competing coating processes are discussed to complete the technological comparison for the case of hard chromium deposition.

11 May 2023 in Materials
Verified
Journal Article
Open access
PDF file
AMAntoine Merlo
Antoine Merlo
FDFlorin Duminica
Florin Duminica
ADAlain Daniel
Alain Daniel
GLGrégoire Léonard
Grégoire Léonard
Due to the toxicity associated with chromium electrodeposition, alternatives to that process are highly sought after. One of those potential alternatives is High Velocity Oxy-Fuel (HVOF). In this work, a HVOF installation is compared with chromium electrodeposition from environmental and economic points of view by using Life Cycle Assessment (LCA) and Techno-Economic Analysis (TEA) for the evaluation. Costs and environmental impacts per piece coated are then evaluated. On an economic side, the lower labor requirements of HVOF allow one to noticeably reduce the costs (20.9% reduction) per functional unit (F.U.). Furthermore, on an environmental side, HVOF has a lower impact for the toxicity compared to electrodeposition, even if the results are a bit more mixed in other impact categories.

Verified
Conference Paper
Open access
PDF file
AMAntoine Merlo
Antoine Merlo
WKWojciech Kaczan
Wojciech Kaczan
GLGrégoire Léonard
Grégoire Léonard
HWHerbert Wirth
Herbert Wirth
As ore quality declines in KGHM mines after continuous exploitation, it becomes increasingly relevant to extract as much economic value as possible from the mined ore while limiting the environmental impact. The recovery of cobalt from converter slag is a possible extraction route that can increase economic output at a limited environmental and logistic cost. Life cycle assessment (LCA) is used to assess the environmental impact of copper exploitation and to compare that impact with the estimated impact of cobalt extraction in the Lubin mine. In most impact categories, Co extraction would be responsible for less than 0.2% of the impact, while increasing economic output by 3.38%. Economic allocation shows that cobalt recovery is environmentally pertinent.

15 September 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
AMAntoine Merlo
Antoine Merlo
AOAidan O&Apos;Neil
Aidan O&Apos;Neil
ETEleanor Thomas
Eleanor Thomas
NMNathan Mariano
Nathan Mariano
OQOlivia Quinn
Olivia Quinn
EMEric Masanet
Eric Masanet
Decarbonizing industrial heat is critical to mitigating climate change, and low- to medium-temperature (LMT) process heat represents the segment of U.S. manufacturing where short-term abatement potential is greatest. This study presents a novel, bottom-up approach to assess the technical and environmental potential of electrifying LMT industrial heat in the U.S. chemicals, pulp and paper, and food and beverage manufacturing sectors. Using first-principles engineering models and unit-level GHGRP data, this study simulates industrial process heat electrification across 798 (out of an initial sample of 934) of the largest manufacturing facilities in the U.S.Four electrification scenarios are evaluated: drop-in electrification (replacing fossil fuel-fired equipment with electrode boilers and resistance dryers and ovens), drop-in electrification with added energy efficiency measures (reduction in losses and unit energy usage), advanced electrification (with ambient-source heat pumps), and advanced electrification with energy efficiency and waste heat recovery. Results indicate that electrification could reduce natural gas demand of the 934 sampled facilities by up to 66% and coal by 63%, while increasing industrial electricity demand by 158-301 TWh/year (16-30% of current industrial demand). Cumulative GHG emissions reductions from 2025-2050 vary by scenario and sector, with advanced electrification and efficiency measures yielding the greatest reduction due to the advantageous coefficients of performance (1.2-1.8) of heat pumps compared to electrode and natural gas boilers. However, near-term emissions benefits depend on grid decarbonization, with reductions materializing after 2030 under assumed U.S. grid emission factors projections.