Wearable devices gain increasing popularity since they can collect important information for healthcare and well-being purposes. Compared with battery, energy harvesting is a better power source for these wearable devices due to many advantages. However, harvested energy is naturally unstable and program execution will be interrupted frequently. Nonvolatile processors demonstrate promising advantages to back up volatile state before the system energy is depleted. However, it also introduces non-negligible energy and area overhead. In this paper, we aim to reduce the amount of data that need to be backed up during a power failure. Based on the observation that stack size varies along program execution, we propose to analyze the application program and identify efficient backup positions, by which the stack content to back up can be significantly reduced. The evaluation results show an average of 45.7% reduction on nonvolatile stack size for stack backup, with 0.58% storage overhead. In the mean time, with the proposed schemes, the energy utilization and program forward progress can be greatly improved compared with instant backup.
5 January 2017 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
Nonvolatile static random access memory (nvSRAM) has been widely investigated as a promising on-chip memory architecture in energy harvesting sensor nodes, due to zero standby power, resilience to power failures, and fast read/write operations. However, conventional approaches back up all data from static random access memory into nonvolatile memory when power failures happen. It leads to significant energy overhead and peak inrush current, which has a negative impact on the system performance and circuit reliability. This paper proposes a holistic data backup optimization to mitigate these problems in nvSRAM, consisting of a partial backup algorithm and a run-time adaptive write policy. A statistic dead-block predictor is employed to achieve dead block identification with trivial hardware overhead. An adaptive policy is used to switch between write-back and write-through strategy to reduce the rollback induced by backup failures. Experimental results show that the proposed scheme improves the performance by 4.6% on average while the backup power consumption and the inrush current are reduced by 38.1% and 54% on average compared to the full backup scheme. What is more, the backup capacitor size for energy buffer can be reduced by 40% on average under the same performance constraint.
18 July 2018 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
The capacity of SRAM-based FPGA block RAM (BRAM) is restrained by the low density and high leakage power of the current CMOS technology. In this paper, we propose a nonvolatile memory (NVM)-based BRAM architecture which enables flexible conversions between single-level cell (SLC) and multilevel cell (MLC) states. We show that despite the high per-access latency and power consumption, MLC-based BRAM blocks reduce the routing cost between logic units and on-chip data storages, which potentially leads to a smaller critical path delay and power consumption. Therefore, we propose an NVM BRAM architecture and an EDA framework which adaptively packs data into SLC- or MLC-state BRAMs during FPGA design flow in order to achieve better system performance. This paper illustrates that a simple memory device replacement from SRAM to NVM leads to nonoptimal system performance. On the other hand, compared with operating all NVM BRAM blocks in the SLC state with better per-access latency and power consumption, the proposed hybrid SLC-MLC architecture and design flow improves the critical path delay by 18.51%, with a system power reduction of 25.83% at the same time. Moreover, compared with the traditional “fast” SRAM-based BRAM blocks under the same BRAM area constraint, our hybrid NVM BRAM architecture improves the critical path delay by 8.55% on average, with an average system power reduction of 54.34% at the same time.
Wearable, implantable and Internet of Things devices are attracting increasing attention from both research and industry fields. Energy harvesting is a promising alternative of battery to power these embedded systems. However, the intrinsic instability of energy harvesting systems leads to potential frequent power interruptions. In traditional volatile processor, all the status will be lost at power failures and the program needs to re-start after power resumes. In order to survive the power failures and enable accumulative execution, non-volatile processor (NVP) is proposed to back up volatile information before power depletion and recover the system status after power resumes. Non-volatile memory (NVM) is typically attached for cache and main memory backup. There are researches working on optimization of the backup. However, little of them involve multiple level cell (MLC) NVM. In this work, we first discuss the benefit of applying MLC NVM for cache backup and the architecture of morphable hybrid cache, and then propose a three-stage energy-aware cache management strategy to improve the system performance and energy utilization while guaranteeing successful backups. Backup-aware cache replacement policies are also developed for backup optimization. Evaluation shows that the proposed EMC scheme can achieve 10.6 percent performance improvement and simultaneous 25.2 percent energy reduction when compared with the single level cell (SLC) based hybrid cache.