This paper presents a robotic system using Unmanned Aerial Vehicles (UAVs) for bridge-inspection tasks that require physical contact between the aerial platform and the bridge surfaces, such as beam-deflection analysis or measuring crack depth with an ultrasonic sensor. The proposed system takes advantage of the aerodynamic ceiling effect that arises when the multirotor gets close to the bridge surface. Moreover, this paper describes how a UAV can be used as a sensor that is able to fly and touch the bridge to take measurements during an inspection by contact. A practical application of the system involving the measurement of a bridge’s beam deflection using a laser tracking station is also presented. In order to validate our system, experiments on two different bridges involving the measurement of the deflection of their beams are shown.

The article presents a vision system for the autonomous grasping of objects with Unmanned Aerial Vehicles (UAVs) in real time. Giving UAVs the capability to manipulate objects vastly extends their applications, as they are capable of accessing places that are difficult to reach or even unreachable for human beings. This work is focused on the grasping of known objects based on feature models. The system runs in an on-board computer on a UAV equipped with a stereo camera and a robotic arm. The algorithm learns a feature-based model in an offline stage, then it is used online for detection of the targeted object and estimation of its position. This feature-based model was proved to be robust to both occlusions and the presence of outliers. The use of stereo cameras improves the learning stage, providing 3D information and helping to filter features in the online stage. An experimental system was derived using a rotary-wing UAV and a small manipulator for final proof of concept. The robotic arm is designed with three degrees of freedom and is lightweight due to payload limitations of the UAV. The system has been validated with different objects, both indoors and outdoors.

This article presents a software layer to abstract users of unmanned aerial vehicles from the specific hardware of the platform and the autopilot interfaces. The main objective of our unmanned aerial vehicle abstraction layer (UAL) is to simplify the development and testing of higher-level algorithms in aerial robotics by trying to standardize and simplify the interfaces with the unmanned aerial vehicles. Unmanned aerial vehicle abstraction layer supports operation with PX4 and DJI autopilots (among others), which are current leading manufacturers. Besides, unmanned aerial vehicle abstraction layer can work seamlessly with simulated or real platforms and it provides calls to issue standard commands such as taking off, landing or pose, and velocity controls. Even though unmanned aerial vehicle abstraction layer is under continuous development, a stable version is available for public use. We showcase the use of unmanned aerial vehicle abstraction layer with a set of applications coming from several European research projects, where different academic and industrial entities have adopted unmanned aerial vehicle abstraction layer as a common development framework.

This article proposes a novel docking system design for unmanned aerial vehicles (UAVs) that provides measurements of the robot's position at high frequency. These measurements are used to control the aerial robot, enabling it to hover while it performs any kind of manipulation task in GPS-denied industrial environments without causing the UAV to drift or putting at risk the platform and its environment. The novel tool is designed as an arm end effector, preventing the aerial manipulator from colliding while in operation. A cascade controller is proposed to close the position loop. An additional use case for the docking system is described in the "Experimental Validation" section; it consists of performing position-based servoing (PBS) of a second manipulator using the position provided by the docking tool and the manipulator's kinematic model.

This paper presents a crawling mechanism using a soft-tentacle gripper integrated into an unmanned aerial vehicle for pipe inspection in industrial environments. The objective was to allow the aerial robot to perch and crawl along the pipe, minimizing the energy consumption, and allowing to perform contact inspection. This paper introduces the design of the soft limbs of the gripper and also the internal mechanism that allows movement along pipes. Several tests have been carried out to ensure the grasping capability on the pipe and the performance and reliability of the developed system. This paper shows the complete development of the system using additive manufacturing techniques and includes the results of experiments performed in realistic environments.

Giving unmanned aerial vehicles (UAVs) the possibility to manipulate objects vastly extends the range of possible applications. This applies to rotary wing UAVs in particular, where their capability of hovering enables a suitable position for in-flight manipulation. Their manipulation skills must be suitable for primarily natural, partially known environments, where UAVs mostly operate. We have developed an on-board object extraction method that calculates information necessary for autonomous grasping of objects, without the need to provide the model of the object’s shape. A local map of the work-zone is generated using depth information, where object candidates are extracted by detecting areas different to our floor model. Their image projections are then evaluated using support vector machine (SVM) classification to recognize specific objects or reject bad candidates. Our method builds a sparse cloud representation of each object and calculates the object’s centroid and the dominant axis. This information is then passed to a grasping module. Our method works under the assumption that objects are static and not clustered, have visual features and the floor shape of the work-zone area is known. We used low cost cameras for creating depth information that cause noisy point clouds, but our method has proved robust enough to process this data and return accurate results.