The energy autonomy of UAVs is an important direction in the field of aerospace. Long-endurance aerial vehicles allow for continuous flight; however, to meet the guidelines, the power supply system has to be able to harvest energy from outside. Solar cells allow the production of electricity during the day when the sun shines on their surface. Depending on the location, time, weather, and other external factors, the energy produced by PV panels will change. In order to calculate as accurately as possible the energy obtained by solar cells, we developed a simulation model that took into account all of the external restrictions and the UAV’s limits during flight. The conducted analysis made it possible to obtain information for the specific input data on whether the UAV is able to fly for 24 h in a specific flight scenario. The UAV powered by solar cells developed by us and the performed aviation missions have shown that the UAV is capable of continuous flight without the need to land.
A vertical take-off and landing (VTOL) is a type of unmanned aerial vehicle (UAV) that allows for flight in harsh weather for surveillance and access to remote areas. VTOL can be performed without a runway. As such, VOTL UAVs are used in areas where there is limited space and in urban locations. The structural endurance of VTOL UAVs is limited and is further reduced in the case of fixed-wing UAVs. Long-endurance aerial vehicles allow for continuous flight, but their power supply systems must be able to harvest energy from external sources in order to meet the guidelines. The wings of these UAVs are often covered with solar cells. This article presents the extended range and flight time of a tail-sitter VTOL that incorporates solar cells on the UAV structure. A VTOL powered by solar cells can perform aviation missions with fewer landings, allowing for the performance of such UAVs to be increased and for their flight time to be extended several times over those without solar cells. Simulations accounting for the use of PV panels on the UAV structure show that depending on the scenario and flight date, VTOLs can double the flight time on the spring equinox and increase the flight time by more than six times on the summer solstice.
Achieving energy autonomy in a UAV (unmanned aerial vehicle) is an important direction for aerospace research. Long endurance flights allow for continuous observations, taking of measurements and control of selected parameters. To provide continuous flight, a UAV must be able to harvest energy externally. The most popular method to achieve this is the use of solar cells on the wings and structure of the UAV. Flexible solar cells mounted on the surface of the wings can be damaged and contaminated. To prevent these negative changes, it is necessary to apply a protective coating to the solar cells. One of the more promising methods is lamination. To properly carry out this process, some parameters have to be appropriately adjusted. The appropriate selection of temperature and feed speed in the laminator allows a PV (photovoltaic) panel to be coated with film, minimizing any defects in the structure. Covering PV panels with film reduces the performance of the solar cells. By measuring the current–voltage characteristics, data were obtained showing the change in the performance of solar cells before and after lamination. In the case of testing flexible PV panels, the efficiency decreased from 24.29 to 23.33%. This informed the selection of the appropriate number of solar cells for the UAV, considering the losses caused by the lamination process.
This article presents the results of work related to the power supply system for 10kW electric, rental go-kart. The research took into account a few types of battery cells. For the case study, the best option was chosen taking into account the restrictions included in the multicriteria analysis for further application. Chosen BLDC motor and battery type were tested on test stands and simulated in MATLAB/Simulink. Simulation model allowed to compare the characteristics from test stands and simulation and next tune the model. Minimum capacity of the batteries had to allow for at least 20 minutes of drive. Chosen elements: electric motor, motor controller, battery cells, BMS allowed to build the first prototype. Tests in real conditions showed the difference between simulation and research system. We could notice what to improve to tune the simulation model and the kart power supply system.
This article presents the results of work related to design, analysis and selection of the electric motors, servos and elements of motion system for 3D printed snakebot. Electric motors and servos had to meet a number of requirements like dimensions, torque, RPM. The drivetrain allowed to drive the snakebot and rotate system allowed to torsional movement between adjacent robot modules. CAD model and analysis allowed to select the proper elements of drivetrain and rotate system. We built test stands and after verification we built the prototype. Next step after building the robot was to carry out tests to verify the mobility of the snake robot. We checked, among others, movement of servos in different planes, snakebot speed, driving at angle (up and down).
This article presents the results of work related to the design, analysis, and manufacturing of the shaft for an electric go-kart. Works considered the stiffness of the shaft for various conditions affecting the vehicle while driving. In the previous stage of the project, the electric motor and gear transmission were selected. The main goal of this case study was to design the shaft for 10 kW electric go-kart. The rear driving axle of the go-kart is not equipped with a differential. The equal rotational speed of two rear wheels causes that occurs skidding and greater forces acting on the vehicle and driver when cornering. We were considering two types of the shaft – full and drilled. The first one provides greater stiffness, the second one is “softer”. The analysis allowed for the selection of a more appropriate shaft, and then for its manufacture and assembly in the vehicle.