Ceramic matrix composites (CMCs) are well-established composites applied on commercial, laboratory, and even industrial scales, including pottery for decoration, glass–ceramics-based light-emitting diodes (LEDs), commercial cooking utensils, high-temperature laboratory instruments, industrial catalytic reactors, and engine turbine blades. Despite the extensive applications of CMCs, researchers had to deal with their brittleness, low electrical conductivity, and low thermal properties. The use of carbon nanotubes (CNTs) as reinforcement is an effective and efficient method to tailor the ceramic structure at the nanoscale, which provides considerable practicability in the fabrication of highly functional CMC materials. This article provides a comprehensive review of CNTs-reinforced CMC materials (CNTs-CMCs). We critically examined the notable challenges during the synthesis of CNTs-CMCs. Five CNT dispersion processes were elucidated with a comparative study of the established research for the homogeneity distribution in the CMCs and the enhanced properties. We also discussed the effect of densification techniques on the properties of CNTs-CMCs. Additionally, we synopsized the outstanding microstructural and functional properties of CNTs in the CNTs-CMCs, namely stimulated ceramic crystallization, high thermal conductivity, bandgap reduction, and improved mechanical toughness. We also addressed the fundamental insights for the future technological maturation and advancement of CNTs-CMCs.
This work focused on the influence of carbon nanotubes (CNT) to the microstructural properties of Zn2SiO4/CNT (ZSO/CNT) composite. CNT was synthesized via alcohol catalytic chemical vapor deposition (ACCVD) using cobalt oxide as catalyst and ethanol as carbon source. Zinc silicate (ZSO) glass was prepared from quenching the melted commercial waste glass bottle with zinc oxide powder. ZSO/CNT-x composites with various CNT concentration (0, 1, 2 and 3 wt%) was prepared through introducing CNT into ZSO glass via dry processing technique followed by sintering process in Argon gas (Ar) environment and atmospheric (atm) environment, respectively. FESEM, XRD and EDS were employed to determine the surface morphology, phase composition and elemental distribution of sintered sample. Crystallite trigonal willemite (Zn2SiO4) phase was observed from argon sintered sample and the crystallite size of willemite phase in ZSO/CNT-3/Ar showed the most reduced lattice strain of 22.85% compared to ZSO/CNT-0/Ar. In contrast, semi-crystalline phase exhibited in atmospheric sintered sample resulted in high lattice strain. It is concluded that dry powder processing and inert gas thermal treatment can be an effective technique in fabricating strain-reduced ceramics/CNT composite without alternating the domain phase. Least internal strain in crystal lattice have potential on enhancing the luminescence properties of phosphor material and lattice thermal conductivity of thermoelectric material.
In this work, the potential of utilizing a waste latex-based precursor (i.e., natural rubber glove (NRG)) as a carbon source for carbon nanotube (CNT) fabrication via chemical vapor deposition has been demonstrated. Gas chromatography-mass spectroscopy (GC-MS) analysis reveals that the separation of the lightweight hydrocarbon chain from the heavier long chain differs in hydrocarbon contents in the NRG fraction (NRG-L). Both solid NRG (NRG-S) and NRG-L samples contain >63% carbon, <0.6% sulfur and <0.08% nitrogen content, respectively, as per carbon-nitrogen-sulfur (CNS) analysis. Growth of CNTs on the samples was confirmed by Raman spectra, SEM and TEM images, whereby it was shown that NRG-S is better than NRG-L in terms of synthesized CNTs yield percentage with similar quality. The optimum vaporization and reaction temperatures were 350 and 800 °C, respectively, considering the balance of good yield percentage (26.7%) and quality of CNTs (ID/IG = 0.84 ± 0.08, diameter ≈ 122 nm) produced. Thus, utilization of waste NRG as a candidate for carbon feedstock to produce value-added CNTs products could be a significant approach for eco-technology.
17 December 2024 in Materials Chemistry and Physics