This paper presents an experimental program performed to study the effect of fluid-structure interaction on the modal dynamic response of water-surrounded slender bridge pier with pile foundation. A reduced scale slender bridge pier specimen is built and tested through forced vibration method. The vibration periods of the first four lateral modes, including the first two modes along x-axis and the first two modes along y-axis, are measured based on the specimen submerged by 16 levels of water and designated with 4 levels of tip mass. Three-dimensional (3D) finite-element models are established for the tested water-pier system and analyzed under various combined cases of water level and tip mass. Percentage increases of vibration periods with respect to dry vibration periods (i.e., vibration periods of the specimen without water) are determined as a function of water level and tip mass to evaluate the effect of fluid-structure interaction. The numerical results are successfully validated against the recorded test data. Based on the validated models, the modal hydrodynamic pressures are calculated to characterize the 3D distribution of hydrodynamic loads on the pier systems. The research provides a better illumination into the effect of fluid-structure interaction on the modal dynamic response of deepwater bridges.

This study aims to analyze the longitudinal seismic performance of a typical multi-span continuous girder bridge with seat-type abutments under earthquake excitation, especially accounting for different abutment behaviors. Three-dimensional finite element models of typical multi-span bridges are built considering the nonlinearity of the bridge columns, bearings, abutment-backfill interactions, pile-soil interactions, and the pounding at expansion joints. One of the models adopts a simplified bilinear model to express the force-displacement relationship of the abutment backwall. The other adopts a more practical multi-linear model, and the abutment backwall is used as a sacrificial component to control the damage to the abutment’s foundation by changing the strength of the abutment backwall. Comparisons of the results of the analysis of two bridge models with and without a sacrificial backwall indicate that it is more favorable for bridges with a sacrificial backwall to protect the foundation, but it is likely to arouse a larger displacement response of the main beam and even cause the unseating of girders. The recommendation for a sacrificial abutment in seismic design is that the right yield strength of the backwall should be selected to reach the balance point of force and displacement, and a collapse-proof system could be employed to prevent the beam from unseating.

In this study, based on an actual project, the steel wire in the suspender of a concrete-filled steel tube arch bridge was selected from appropriate samples to perform acetic acid-accelerated salt spray tests, and steel wire samples with different corrosion degrees were obtained. A laser microscope was used to measure the roughness of the samples, and three corrosion samples were randomly selected from each group for grinding. Fatigue tests were performed on steel wire samples with different degrees of corrosion and polished steel wire samples, and the fatigue fracture was observed and analyzed. The results showed that few cracks on the steel wire surface could be eliminated by grinding, and the fatigue life of the specimens could be increased. Finally, the stress-life-mass loss rate (S-N-η) probability model based on the Weibull distribution was obtained using the measured fatigue data, which can be further referenced in the planning of the inspection of suspender service status, steel wire corrosion protection, and fatigue life prediction, etc.

The suspenders on the sides of an arch bridge are highly vulnerable to damage caused by traffic load and environmental corrosion. To accurately estimate the cable force of suspenders, herein, we analyse the influencing factors through a suspender tension test based on the principle of suspender vibration. The frequency of each suspender of the bridge is evaluated using the frequency method. By combining the cable force data measured directly and the measured suspender frequency, the formulas for calculating the cable forces of long and short suspenders are fitted, and a reasonable estimation method for the calculated length of short suspenders is provided. The formulas are verified through application to a CFST arch bridge. Results indicate that the proposed formula effectively considers the influence of the sleeve on the overall calculated length of the suspender. The formula calculates the suspender cable force with higher accuracy, proving its suitability for engineering use.

The corrosion and degradation behavior of high-strength steel wires during service directly affect the safety and usability of suspenders in steel pipe concrete arch bridges. In this study, three different types of specimens were fabricated using steel wires extracted from the suspenders of an 11-year-old in-service arch bridge and subjected to accelerated corrosion tests with acetic acid. Considering the differential diffusion processes of corrosion factors caused by varying degrees of damage to the suspender sheath, the spatial corrosion variability of steel wires at different positions within the suspender cross-section was investigated. Experimental results indicated a two-stage characteristic in the corrosion process of individual galvanized steel wire samples. In the first corrosion stage, the microstructure on the corroded steel wire surface evolved from a dense crystalline structure to a porous one. In the second corrosion stage, corrosion products accumulate on the steel wire substrate, subsequently further aggregating into sheet-like structures. The maximum pitting factor of individual steel wire samples from a specific area could be described by a Type I extreme value distribution. In the time-dependent model that was established, the location parameter and scale parameter exhibited an exponential decrease during the first corrosion stage and a linear decrease during the second corrosion stage. In the absence of sheath protection, the coefficient of variation in corrosion among adjacent steel wires in the suspender followed a normal distribution. The spatial corrosion variability of the wires inside the suspender is significantly influenced by the shape of the suspender sheath damage. As the corrosion time increased, the overall discrepancy in corrosion levels among different layers of wires diminished.