Technological advances have enabled the development of a number of optical fiber sensing methods over the last few years. The most prevalent optical technique involves the use of fiber Bragg grating (FBG) sensors. These small, lightweight sensors have many attributes that enable their use for a number of measurement applications. Although much literature is available regarding the use of FBGs for laboratory level testing, few publications in the public domain exist of their use at the operational level. Therefore, this paper gives an overview of the implementation of FBG sensors for large scale structures and applications. For demonstration, a case study is presented in which FBGs were used to determine the deflected wing shape and the out-of-plane loads of a 5.5-m carbon-composite wing of an ultralight aerial vehicle. The in-plane strains from the 780 FBG sensors were used to obtain the out-of-plane loads as well as the wing shape at various load levels. The calculated out-of-plane displacements and loads were within 4.2% of the measured data. This study demonstrates a practical method in which direct measurements are used to obtain critical parameters from the high distribution of FBG sensors. This procedure can be used to obtain information for structural health monitoring applications to quantify healthy vs. unhealthy structures.
Fiber-reinforced polymer composites are widely used in the aerospace industry due to their high stiffness and strength-to-weight ratios. However, their applicability can be limited by their relatively low interlaminar properties when compared to metallic alternatives. Through-thickness reinforcement approaches, such as stitching, z-pinning, needling, tufting, and three-dimensional weaving, have been developed in recent decades to enhance the interlaminar properties of composites. Stitching is considered to be an efficient and cost-effective method to reinforce composites in the through-thickness direction. Additionally, stitch parameters (stitch density, linear thread density, thread material, pretension, etc.) highly influence the in-plane and out-of-plane properties. This paper summarizes results from over one hundred papers on the influence of stitch parameters on fracture energy, interlaminar strength, and impact characteristics of stitched composite laminates, sandwich composites, and high-temperature composites. Much of the research on the influence of stitch parameters has focused on thermoset polymer matrix composites (PMCs), while fewer studies have investigated the impact of stitch parameters on high temperature or sandwich composites. Modification of existing and new test methods have been developed to adequately measure the effectiveness of stitching on the out-of-plane behavior of PMC panels. Results demonstrate that out-of-plane properties of PMCs are highly dependent on stitch parameters and can be enhanced by through-thickness stitching.
16 October 2008 in Mechanics of Time-Dependent Materials
Fiber-reinforced polymer matrix composites are increasingly considered for lightweight cryogenic pressure vessels due to their excellent combination of tailorability, specific mechanical properties, and relatively low coefficients of thermal expansion. However, significant challenges must be overcome to fully utilize PMCs for cryogenic fuel tanks in terms of transverse microcracking and subsequent permeation of cryogenic fuel. Gas permeation and microcrack densities of cryogenically cycled composites are highly influenced by their layup, ply thickness, load case, and manufacturing defects like voids and resin rich zones. There has been a significant amount of research on measuring gas permeation of composites fatigued under pure thermal or uniaxial thermo-mechanical stresses. However, results demonstrate that the gas permeability should be measured under biaxial thermo-mechanical stresses to properly gauge the leakage characteristics of damaged composites. This paper summarizes the results from over a hundred papers on the key parameters that influence the gas permeability of composites, appropriate testing methods to cycle composites for permeability measurement, methods to limit the evolution of transverse microcracks, and materials traditionally used for the fabrication of all-composite cryogenic fuel tanks. Thin plies and nanofiller-toughening of the matrix have been shown to provide significant improvements in transverse microcrack suppression within cryogenically cycled composites.
This study investigates the feasibility of using embedded optical fibers in polymer matrix composite laminates to characterize delaminations caused by low-velocity impacts with energies between 30 J and 50 J. Impact damage can occur in composite structures during manufacture, in-service, storage and routine maintenance. Because of their small size and light weight, optical fibers can be embedded in composite structures during the manufacture of composite parts, allowing the structure to be monitored for impact-induced delaminations without being removed from service. In this study, optical fibers are embedded in a grid configuration at four selected locations (one-third from impact surface, midplane, two-thirds from impact surface, and farthest ply from impact) in thick autoclave-cured graphite/epoxy laminates. Low-velocity impact testing is performed at four energy levels. Manufacturing procedures for embedding the optical fibers within the composite laminates are investigated. The strain distribution from the optical fibers is correlated with ultrasonic C-scans of the laminates in which they are embedded. X-ray computed tomography scan images are also compared to those from ultrasonic C-scans. Results indicate that embedded optical fibers can provide post-impact strain responses and delamination area from each embedded site within the impacted laminates.