The heterogeneous phase combination flooding (HPCF) system which is composed of a branched-preformed particle gel (B-PPG), polymer, and surfactant has been proposed to enhance oil recovery after polymer flooding in heterogeneous reservoirs by mobility control and reducing oil–water interfacial tension. However, the high cost of chemicals can make this process economically challenging in an era of low oil prices. Thus, in an era of low oil prices, it is becoming even more essential to optimize the heterogeneous phase combination flooding design. In order to optimize the HPCF process, the injection strategy has been designed such that the incremental oil recovery can be maximized using the corresponding combination of the B-PPG, polymer, and surfactant, thereby ensuring a more economically-viable recovery process. Different HPCF injection strategies including simultaneous injection and alternation injection were investigated by conducting parallel sand pack flooding experiments and large-scale plate sand pack flooding experiments. Results show that based on the flow rate ratio, the pressure rising area and the incremental oil recovery, no matter whether the injection strategy is simultaneous injection or alternation injection of HPCF, the HPCF can significantly block high permeability zone, increase the sweep efficiency and oil displacement efficiency, and effectively improve oil recovery. Compared with the simultaneous injection mode, the alternation injection of HPCF can show better sweep efficiency and oil displacement efficiency. Moreover, when the slug of HPCF and polymer/surfactant with the equivalent economical cost is injected by alternation injection mode, as the alternating cycle increases, the incremental oil recovery increases. The remaining oil distribution at different flooding stages investigated by conducting large-scale plate sand pack flooding experiments shows that alternation injection of HPCF can recover more remaining oil in the low permeability zone than simultaneous injection. Hence, these findings could provide the guidance for developing the injection strategy of HPCF to further enhance oil recovery after polymer flooding in heterogeneous reservoirs in the era of low oil prices.

Surfactant–polymer (SP) flooding has significant potential to enhance oil recovery after water flooding in mature reservoirs. However, the economic benefit of the SP flooding process is unsatisfactory under low oil prices. Thus, it is necessary to reduce the chemical costs and improve SP flooding efficiency to make SP flooding more profitable. Our goal was to maximize the incremental oil recovery of the SP flooding process after water flooding by using the equal chemical consumption cost to ensure the economic viability of the SP flooding process. Thus, a systematic study was carried out to investigate the SP flooding process under different injection strategies by conducting parallel sand pack flooding experiments to optimize the SP flooding design. Then, the comparison of the remaining oil distribution after water flooding and SP flooding under different injection strategies was studied. The results demonstrate that the EOR efficiency of the SP flooding process under the alternating injection of polymer and surfactant–polymer (PASP) is higher than that of conventional simultaneous injection of surfactant and polymer. Moreover, as the alternating cycle increases, the incremental oil recovery increases. Based on the analysis of fractional flow, incremental oil recovery, and remaining oil distribution when compared with the conventional simultaneous injection of surfactant and polymer, the alternating injection of polymer and surfactant–polymer (PASP) showed better sweep efficiency improvement and recovered more remaining oil trapped in the low permeability zone. Thus, these findings could provide insights into designing the SP flooding process under low oil prices.

Polymer gels have been successfully applied to control undesired water production for many years, however, due to poor long-term thermal stability and salt tolerance, conventional polymer gels present some limitations for application in high temperature and high salinity reservoirs. In this paper, an organic/inorganic combined gel composed of polymer with low degree of hydrolysis, phenol formaldehyde resin and inorganic silicate was proposed and developed. The effects of concentration, temperature on gelation time were studied. Long-term thermal stability, salt tolerance and permeability reduction ability were investigated. Results showed that based on proper gelation time and economical cost, the formulation of the organic/inorganic combined gel was optimized. The gelation time decreased from 54.0 to 15.5 h with increasing temperature from 100 to 130 °C. After aging for 60 days in simulated formation brine with high total dissolved solids (TDS: 20 % NaCl + 2.5 % CaCl₂) at 130 °C, compared with polymer gel, the organic/inorganic combined gel had better long-term thermal stability and salt tolerance. Sandpack flow experimental results showed that for the organic/inorganic combined gel composed of 0.3 wt% polymer, 4.0 wt% resin and 3.0 wt% inorganic silicate, after aging for 60 days at 130 °C, the combined gel showed approximately 85 % permeability reduction. Therefore, these results indicate that the combined gel studied here can be a good candidate for controlling water production in high temperature and high salinity reservoirs.

Polymer flooding has a significant potential to enhance oil recovery in a light oil reservoir. However, for polymer flooding in a conventional heavy oil reservoir, due to unfavorable mobility ratio between water and oil, the improvement of sweep efficiency is limited, resulting in a low incremental oil recovery and failure to achieve high-efficiency development for polymer flooding in a conventional heavy oil reservoir. Inspired by the EOR mechanisms of the surfactant-polymer (SP) flooding process, the polymer-viscosity reducing surfactant flooding (P-VRSF) system was proposed to enhance conventional heavy oil recovery. Thus, to gain an insight into enhancing oil recovery by P-VRSF in a conventional heavy oil reservoir, the viscosity property, oil-water interfacial tension property, and oil viscosity reduction property were investigated. A series of parallel sand pack experiments were conducted to investigate enhanced oil recovery ability of polymer flooding and P-VRSF in a heterogeneous reservoir. Then, the 2D micromodel flooding experiments were conducted to investigate the EOR mechanism from porous media to pore level. Results demonstrated that polymer could increase the viscosity of injection water and improve the sweep efficiency. The emulsifying stability of surfactant with ultralow IFT (10^-3mN/m) was worse than that of the surfactant with higher IFT (10^-2mN/m). The viscosity reduction rate of the surfactant with higher IFT was higher than 80 at different oil-water volume ratios. The incremental oi recovery of P-VRSF was higher than that of polymer flooding. Moreover, the polymer-viscosity reducing surfactant with higher IFT could have higher incremental oil recovery. The 2D micromodel flooding results showed that the swept area of polymer flooding and P-VRSF was larger than that of water flooding. Moreover, the swept area of the surfactant with good emulsifying stability was larger than that of the surfactant with ultralow IFT. These findings could provide insights into enhancing oil recovery by P-VRSF in the conventional heavy oil reservoir.