Anchasa Pramuanjaroenkij

Dr. Anchasa Pramuanjaroenkij


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 December 2022 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
APAnchasa Pramuanjaroenkij
Anchasa Pramuanjaroenkij
SKSadık Kakaç
Sadık Kakaç

1 May 2016 in Journal of Engineering Physics and Thermophysics
Verified
Journal Article
Closed access
PDF file
SKS. Kakaç
S. Kakaç
APAnchasa Pramuanjaroenkij
Anchasa Pramuanjaroenkij

21 January 2024 in Thermal Science and Engineering Progress
Verified
Journal Article
Closed access
PJPhongsathon Janthasri
Phongsathon Janthasri
APAnchasa Pramuanjaroenkij
Anchasa Pramuanjaroenkij
SKSadık Kakaç
Sadık Kakaç
CCChatchapol Chungchoo
Chatchapol Chungchoo
TNTawee Ngamvilaikorn
Tawee Ngamvilaikorn

1 January 2008
Verified
Book Chapter
Closed access
PDF file
APAnchasa Pramuanjaroenkij
Anchasa Pramuanjaroenkij
SKS. Kakaç
S. Kakaç
XZX. Y. Zhou
X. Y. Zhou

1 January 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
APAnchasa Pramuanjaroenkij
Anchasa Pramuanjaroenkij
JBJ. Bunta
J. Bunta
JTJ. Thiangpadung
J. Thiangpadung
SSS. Sansaradee
S. Sansaradee
PKP. Kamsopa
P. Kamsopa
ATA. Tongkratoke
A. Tongkratoke
Development of diagnostic technique of microfluidic or lab-on-a-chip (LOCs) is currently of great interest for researchers and inventors for their many advantages. It can be used as a real laboratory was many ways to help to the diagnosis faster. This research aims to develop Polydimethylsiloxane (PDMS) lab-on-a-chip (LOCs) which were produced from different molds; the silicon wafer mold and the stainless mold to investigate the flow of the biological sample as the flow in nanochannels. In addition, this research proposes a means to leakage and the blockage of the channel flow. The experimental results were found that the LOCs casted from the silicon wafer mold sandwiched by both the plasma cleaner machine and H shaped acrylic sheets showed leakages around the electrode areas because the first new electrodes were too thick, the proper thickness of the nickel electrode was at 0.05 millimeters. The LOCs casted from the stainless mold were inserted by the nickel electrodes produced by the from the prototype shaped electroplating process; this LOCs using nickel plated electrodes 2 times to make a groove on the nickel electrode backsides when pouring the PDMS into the LOCs casted from the stainless mold. It was found that PDMS was able to flow under the nickel electrode and the PDMS sheet could stick with the glass slide smoothly. In conclusion, it was possible to develop these LOC designs and new electrode fabrications continually under helps from Micro-Electro-Mechanical system, Thailand National Electronics and Computer Technology Center, since causes of the LOC problems were found, and demonstrated the feasibility of developing the LOCs for chemical detection and disease diagnostics.

31 October 2022 in Isı Bilimi ve Tekniği Dergisi
Verified
Journal Article
Closed access
PDF file
SCSaharat Chunthum
Saharat Chunthum
APAnchasa Pramuanjaroenkij
Anchasa Pramuanjaroenkij
SPSiriluk Phankhoksoong
Siriluk Phankhoksoong
RCRungsima Chollakup
Rungsima Chollakup
SKSadık KAKAC
Sadık KAKAC
This research aimed to find the process of value adding for glass wool waste from the glass wool composite board used in the vehicle industry. The waste was reprocessed to be an insulator and to determine the suitable conditions for hot-press forming to create new materials having high thermal resistant properties. Firstly, the properties of the original board; the thermal resistances (R) and the noise absorption coefficients (NRC), were measured and were found averages of 0.9055 m2K/W and 0.3955, respectively. The reprocessing conditions were varied by 2 levels; high and low, of 5 control factors; density, thickness, pressure, temperature, and surface roughness. Three repeating processes for each condition were performed. The Design of Experiment (DoE) was the full factorials; 25 experiments, by using the Analysis of Variance (ANOVA) to find main and interaction factors relating to the properties. From the ANOVA results with the α level of significance at 0.05, it was found that the main factors responding to the high values of the thermal resistance were the thickness and density. This resulted in the suitable conditions for the hot-press process of both the new smooth and rough pads with a density of 96 kg/m3 and a thickness of 25 mm. The R values of the new insulators were in between 0.88 – 0.98 m2K/W and, additionally, the high NRC values were also provided in between 0.46 – 0.49. These findings could be applied for wall designing, wall decorations and heat shields for indoor rooms and different types of buildings.