Nickel iron oxide (NiFe2O4) catalyst was prepared by the combustion reaction method and characterized by XRD, N2 adsorption/desorption, thermogravimetric analysis (TG), and temperature programmed reduction (TPR). The catalyst presented a mixture of oxides, including the NiFe2O4 spinel and specific surface area of 32.4 m2 g−1. The effect of NiFe2O4 catalyst on the supercritical water gasification (SCWG) of eucalyptus wood chips was studied in a batch reactor at 450 and 500 °C without catalyst and with 1.0 g and 2.0 g of catalyst and 2.0 g of biomass for 60 min. In addition, the recyclability of the catalyst under the operating conditions was also tested using recovered and recalcined catalysts over three reaction cycles. The highest amount of H2 was 25 mol% obtained at 450 °C, using 2 g of NiFe2O4 catalyst. The H2 mol% was enhanced by 45% when compared to the non-catalytic test, showing the catalytic activity of NiFe2O4 catalyst in the WGS and the steam reforming reactions. After the third reaction cycle, the results of XRD demonstrated formation of coke which caused the deactivation of the NiFe2O4 and consequently, a 13.6% reduction in H2 mol% and a 5.6% reduction in biomass conversion.
Many countries have adopted the addition of biodiesel to diesel as a way of inserting renewable content into mineral fuel and making a contribution to the environment. The addition of ethanol to the diesel/biodiesel blend to increase the renewable content of the added fuel blend and reduce the percentage of biodiesel could be a strategysince the demand for biodiesel production is high, and this fuel has a high production cost when compared to ethanol. Thus, this study evaluated the performance and the content of NOx, CO and CO2 exhaust gases from a diesel engine fueled with blends of diesel/biodiesel/ethanol: pure B7, B7E3 (B7 with 3% ethanol) and B7E10 (B7 with 10% ethanol). Emissions of fuel blends were evaluated using the engine speed variation and tested at a speed of 1500 rpm under constant load (185 Nm). Assays were performed at engine speeds of 1000, 1100, 1250, 1500 and 1750 rpm and with loads of 10, 25, 50, 75 and 100% of the maximum torque. Through the performance curves, the specific consumption and thermal efficiency were evaluated. The increase in speed and ethanol content in the diesel/biodiesel mixture increased approximately 5 to 7 and 1.4 times, respectively, in terms of the emission of exhaust gases. There was a 6% decrease in the maximum torque and power available at each speed with increasing ethanol content in the blend. However, in a vehicular application, this decrease would be perceived only at some points of the part-load regime, causing considerable reductions in thermal efficiency.
The objective of this paper is to present a review of current research on the valuation of ecosystem services, using emergy evaluation methodology (EME). A bibliometric analysis and a systematic review were carried out between 2000 and 2020, using all of Web of Science database subfields that collected 187 papers, selected through the keywords “emergy” and “ecosystem services”. In the second part of the research, we carried out a new search on Web of Science of the 187 initial articles produced, with the words “valuation” and “economic”, in order to analyze those directly related to the evaluation of ecosystem services. The results showed that the EME method is an effective tool to evaluate ecosystem services, since it relates economic and ecological aspects in the evaluations. The research also indicated that the use of isolated methods does not appear to be the most appropriate solution, and that emergy used in combination with other methodologies can be used to obtain more accurate and comprehensive results to evaluate natural resources.
Biofuels provide high oxygen content for combustion and do modify properties that influence the engine operation process such as viscosity, enthalpy of vaporization, and cetane number. Some requirements of performance, fuel consumption, efficiency, and exhaust emission are necessary for the validation of these biofuels for application in engines. This work studies the effects of the use of diethyl ether (DEE) in biodiesel-ethanol blends in a DI mechanical diesel engine. The blends used in the tests were B80E20 (biodiesel 80%-ethanol 20%) and B76E19DEE5 (biodiesel 76%-ethanol 19%-DEE 5%). Fossil diesel (D100) and biodiesel (B100) were evaluated as reference fuels. The results revealed similar engine efficiencies among tested fuels at all loads. The use of B100 increased CO and NOx and decreased THC compared to D100 at the three loads tested. B80E20 fuel showed an increase in NOx emission in comparison with all fuels tested, which was attributed to higher oxygen content and lower cetane number. THC and CO were also increased for B80E20 compared to B100 and D100. The use of B76E19DEE5 fuel revealed reductions in NOx and CO emissions, while THC emissions increased. The engine efficiency of B76E19DEE5 was also highlighted at intermediate and more elevated engine load conditions.