Atif Rasheed

Mr. Atif Rasheed

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 August 2016 in Polymers
Verified
Journal Article
Open access
PDF file
ARAtif Rasheed
Atif Rasheed
Islam ShyhaIslam Shyha
Islam Shyha
Fawad InamFawad Inam
Fawad Inam
Monolithic epoxy, because of its brittleness, cannot prevent crack propagation and is vulnerable to fracture. However, it is well established that when reinforced—especially by nano-fillers, such as metallic oxides, clays, carbon nanotubes, and other carbonaceous materials—its ability to withstand crack propagation is propitiously improved. Among various nano-fillers, graphene has recently been employed as reinforcement in epoxy to enhance the fracture related properties of the produced epoxy–graphene nanocomposites. In this review, mechanical, thermal, and electrical properties of graphene reinforced epoxy nanocomposites will be correlated with the topographical features, morphology, weight fraction, dispersion state, and surface functionalization of graphene. The factors in which contrasting results were reported in the literature are highlighted, such as the influence of graphene on the mechanical properties of epoxy nanocomposites. Furthermore, the challenges to achieving the desired performance of polymer nanocomposites are also suggested throughout the article.

14 January 2017 in Polymers
Verified
Journal Article
Open access
PDF file
Mohd Shahneel SaharudinMohd Shahneel Saharudin
Mohd Shahneel Saharudin
ARAtif Rasheed
Atif Rasheed
Fawad InamFawad Inam
Fawad Inam
The influence of short-term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength, tensile strength, and impact strength in dry and wet conditions. After short-term water exposure, the maximum microhardness, tensile, flexural and impact toughness values were observed at 0.1 wt % multi-layer graphene (MLG). The microhardness increased up to 50.3%, tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples, the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to the plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of the nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at a concentration of 0.1 wt % to produce considerable improvement in the mechanical properties of the produced hybrid nanocomposites.

1 July 2016 in Polymers
Verified
Journal Article
Open access
PDF file
ARAtif Rasheed
Atif Rasheed
Fawad InamFawad Inam
Fawad Inam
Influence of topographical features on mechanical properties of 0.1 wt % Multi-Layer Graphene (MLG)/clay-epoxy nanocomposites has been studied. Three different compositions were made: (1) 0.1 wt % MLG-EP; (2) 0.1 wt % clay-EP and (3) 0.05 wt % MLG-0.05 wt % clay-EP. The objective of making hybrid nanocomposites was to determine whether synergistic effects are prominent at low weight fraction of 0.1 wt % causing an improvement in mechanical properties. The topographical features studied include waviness (Wa), roughness average (Ra), root mean square value (Rq) and maximum roughness height (Rmax or Rz). The Rz of as-cast 0.1 wt % MLG-EP, clay-EP and 0.05 wt % MLG-0.05 wt % clay-EP nanocomposites were 43.52, 48.43 and 41.8 µm respectively. A decrease in Rz values was observed by treating the samples with velvet cloth and abrasive paper 1200P while increased by treating with abrasive papers 320P and 60P. A weight loss of up to 16% was observed in samples after the treatment with the abrasive papers. It was observed that MLG is more effective in improving the mechanical properties of epoxy than nanoclay. In addition, no significant improvement in mechanical properties was observed in hybrid nanocomposites indicating that 0.1 wt % is not sufficient to generate conspicuous synergistic effects.

5 January 2017 in Preprints.org
Verified
Preprint
Open access
PDF file
Mohd Shahneel SaharudinMohd Shahneel Saharudin
Mohd Shahneel Saharudin
ARAtif Rasheed
Atif Rasheed
Fawad InamFawad Inam
Fawad Inam
The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

16 January 2021 in Applied Physics A
Verified
Journal Article
Open access
PDF file
ARAtif Rasheed
Atif Rasheed
The diffusion at atomic scale is of considerable interest as one of the critical processes in growth and evaporation as well as a probe of the forces at an atomically flat reconstructed surface. This atomic-scale migration is critical to investigate in strontium titanate (SrTiO 3 ) as it possesses the same status in oxide electronics as does silicon in ordinary electronics based on elemental semiconductors. Here we show that (001) terminated SrTiO 3 reconstructed surface is atomically unstable enough to allow atom-vacancy hopping at room temperature. In this work, SrTiO 3 (001) single crystal (7 × 2 × 0.5 mm) was sputtered (0.5 keV, 2.5 µA, 10 min) and annealed multiple times in ultra-high vacuum (UHV) and imaged using scanning tunneling microscope (STM). A relatively unstable surface was observed at low-temperature annealing and tip–surface interactions caused dislocation of mass at the surface. Both square and zig-zag nanolines were observed with atomic resolution where an atom-vacancy hopping was observed in a square diline while imaging at room temperature. The hopping was ceased when sample was annealed at higher temperature and a more compact network of nanolines was achieved. Graphic

1 March 2021 in Journal of Crystal Growth
Verified
Journal Article
Closed access
ARAtif Rasheed
Atif Rasheed