Pharmaceutical products and dyes are the main environmental pollutants in the effluent of textile, cosmetic, and pharmaceutical industries. Therefore, in this study, the central composite design (CCD) based on the response surface methodology (RSM) was used to investigate the operating parameters and determine the optimal conditions for the removal of enrofloxacin (ENF) and Rhodamine B (RhB) by graphene oxide (GO). The structure and morphology of GO were studied using scanning electron microscopes (SEM) and X-ray diffraction (XRD) techniques. Quadratic model was confirmed to describe each of the removal efficiency responses (%R) a with high correlation coefficient (R2 = 0.9987 for ENF and R2 = 0.9999 for RhB) (R2-Adj = 0.9963 for ENF and R2-Adj = 0.9991 for RhB). In optimal conditions, RhB concentration of 10 mg L−1, adsorbent amount of 0.24 g, sonication time of 23 min, ENF concentration of 10 mg L−1, and pH 7, removal rates of more than 92.5% were obtained for both analytes. Adsorption equilibrium was studied with Langmuir, Freundlich, Langmuir-Freundlich, Redlich-Peterson, Toth and Khan isotherm models. Equilibrium data were best fitted with the Langmuir-Freundlich isotherm model. Maximum adsorption capacity of ENF and RhB on GO were 45.035 mg g−1 and 107.230 mg g−1, respectively. The recyclability of GO was evaluated during the ENF and RhB adsorption process. The results showed that up to 4 cycles of adsorbent, the adsorption efficiency is reduced by a tiny amount. The present study showed that GO is highly effective in removing ENF and RhB from environmental water samples.
In the present study, the simultaneous removal of malachite green (MG) and auramine-O (AO) dyes from the aqueous solution by NaX nanozeolites in a batch system is investigated. Taguchi method and response surface methodology (RSM) were used to optimize and model dye removal conditions. In order to do so, the effect of various factors (dyes concentration, sonication time, ionic strength, adsorbent dosage, temperature, and pH of the solution) on the amount of dye removal was evaluated by the Taguchi method. Then, the most important factors were chosen and modeled by the RSM method so as to reach the highest percentage of dye removal. The proposed quadratic models to remove both dyes were in good accordance with the actual experimental data. The maximum removal efficiencies of MG and AO dyes in optimal operating conditions were 99.07% and 99.61%, respectively. Also, the coefficients of determination (R2) for test data were 0.9983 and 0.9988 for MG and AO dyes, respectively. The reusability of NaX nanozeolites was evaluated during the adsorption process of MG and AO. The results showed that the adsorption efficiency decreases very little up to five cycles. Moreover, NaX nanozeolites were also applied as adsorbents to remove MG and AO from environmental water samples, and more than 98.1% of both dyes were removed from the solution in optimal conditions.
As the world population continues to grow, so does the pollution of water resources. It is, therefore, important to identify ways of reducing pollution as part of our effort to significantly increase the supply of clean and safer water. In this study, the efficiency of ultrasound-assisted dispersive liquid–liquid microextraction (UA-DLLME) as a fast, economical, and simple method for extraction malachite green (MG) and rhodamine B (RB) dyes from water samples is investigated. In optimal conditions, the linear dynamic range (LDR) for RB and MG is 7.5–1500 ng mL−1 and 12–1000 ng mL−1, respectively. The limit of detection (LOD) is 1.45 ng mL−1 and 2.73 ng mL−1, and limit of quantification (LOQ) is 4.83 ng mL−1 and 9.10 ng mL−1 for RB and MG, respectively. Extraction efficiency is obtained in the range of 95.53–99.60%. The relative standard deviations (RSD) in real water and wastewater samples are less than 3.5. The developed method is used successfully in the determination of RB and MG dyes from water samples and there are satisfactory results.
19 February 2019 in Water Conservation Science and Engineering
The aim of the present study is to remove dyes from aqueous solutions since the dye compounds are harmful to human life and the environment. Nano-zero-valent iron particles were synthesised and used to remove the synchronisation of Direct Red-31 (DR-31) and Direct Brown-2 (DB-2). Nano-zero-valent iron particles were characterised using SEM (scanning electron microscopy) and XRD (X-Ray Diffraction) analysis. The effects of five influential variables were investigated on the dye removal including DR-31 and DB-2 concentrations (4–20 mg L−1), NZVI dosage (0.15–0.95 g), pH of the solution (5–9) and contact time (20–140 s). In order to improve the conditions, the response surface methodology (RSM) approach was applied using the central composite design (CCD). The response for the removal of DR-31 and DB-2 was predicted second-order polynomial models. The Analysis of Variance (ANOVA) presented that second-order models, with high F-value, were so remarkable in order to eliminate the simultaneity of dyes. Based on the results of the perturbation plot, NZVI dosage and pH of the solution had the most effect on the removal of the dye mixture compared to three other factors. The optimum variables are achieved: NZVI dosage (0.75 g), DR-31 concentration (12.00 mg L−1), DB-2 concentration (12.00 mg L−1), contact time (110.00 s) and pH of the solution (6). Under optimal conditions, the removal rate of DR-31 and DB-2 was 91.03% and 94.57%, respectively. The NZVI can be used effectively to salvage pollution problems posed by anionic dyes in the environment.
27 February 2019 in International Journal of Environmental Science and Technology