Yukang Xu

Dr. Yukang Xu


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 November 2021 in Cellulose
Verified
Journal Article
Closed access
PDF file
XSXueyang Song
Xueyang Song
CFCuicui Fang
Cuicui Fang
YLYuanyuan Li
Yuanyuan Li
PWPing Wang
Ping Wang
YZYan Zhang
Yan Zhang
YXYukang Xu
Yukang Xu

9 February 2022 in Smart Materials and Structures
Verified
Journal Article
Closed access
JZJia-Wen Zhang
Jia-Wen Zhang
YZYan Zhang
Yan Zhang
Yuanyuan LiYuanyuan Li
Yuanyuan Li
XYXu Ye
Xu Ye
PWPing Wang
Ping Wang
YXYukang Xu
Yukang Xu
Three most common methods for preparing PEDOT (poly(3,4-ethylenedioxythiophene)) are studied, including vapor phase polymerization (VPP), in-situ dipping (ISD) and solution deposition (SD) techniques. The PEDOT coated nonwoven fabric (PEDOT@NWF) composites were successfully fabricated via these three processes and have been proven to be conductive and equipped with piezoresistive properties. For each preparation method, factors that may affect product properties, such as concentrations of reagents, reaction temperature, reaction time, etc were explored to summarize the optimal parameters. The PEDOT@NWF composites prepared via different fabrication techniques were analyzed and compared through a series of tests and characterizations. The sensing performance of as-prepared pressure sensors are also been studied. The experimental results demonstrate that PEDOT@NWF prepared by VPP method (PEDOT@NWF-VPP) has the fastest response time (80 ms) and recovery time (40 ms), the composite prepared by ISD method (PEDOT@NWF-ISD) has the highest sensitivity for the pressure range less than 5 kPa (21.162 kPa −1 ) and long-term cycle stability (over 5000 cycles). Sensor utilized PEDOT@NWF-ISD as the piezoresistive layer was assembled and used to detect small pressure such as voice vibrations and air flow, implying that this designed pressure sensor has promising potential in the application of wearable electronic devices and healthcare monitors.

17 May 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SMSara Mosleh
Sara Mosleh
Mulat Alubel ABTEWMulat Alubel ABTEW
Mulat Alubel ABTEW
PBPascal Bruniaux
Pascal Bruniaux
GTGuillaume Tartare
Guillaume Tartare
YXYukang Xu
Yukang Xu
YCYan Chen
Yan Chen
Peoples with spinal disability face a huge problem in the design and development of ergonomically fitted and comfortable clothing. Various research studies on the design and developments of functional clothing for scoliosis patients consider their morphological shapes. However, developing appropriate models of the complicated and deformed anatomical shape of the patient in 3D digitization technologies makes it possible to design a comfortable and fitted garment. The current paper proposes a method for developing a fully parametric 3D adaptive model of the thorax of a patient suffering from scoliosis. The model is designed from the spine and follows the deformation of the spine to adapt the thorax skeleton according to the temporal evolution of the spinal column deformation. The integration of the model of the thorax, adjusted to the patient’s data, enables the chain of acquisition, processing, and global model to be validated. The fit of the model could be improved for the different bones and it is possible to modify the angles of the spine to see the evolution of the disease. The developed model greatly helps to further detect anthropometric points from certain bone parts of the skeleton to design a basic bodice adapted to the patient’s evolving morphology.

12 November 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SMSara Mosleh
Sara Mosleh
Mulat Alubel ABTEWMulat Alubel ABTEW
Mulat Alubel ABTEW
PBPascal Bruniaux
Pascal Bruniaux
GTGuillaume Tartare
Guillaume Tartare
YXYukang Xu
Yukang Xu
Scoliosis is a deformity of the spine that causes disorders of the rib cage. This makes it difficult to design clothes for affected people without following the shape of the rib cage. This paper presents a new 3D clothing design method based on virtual reality for women with physical disabilities such as scoliosis. The current design method is a variation of the draping techniques commonly used by fashion designers to design clothes on a mannequin or human body. However, the current design process highly considers the skeleton and body scan of the person. The skeleton is used to detect the anthropometric points of the patient, while the body scan allows us to detect the morphological contours at the onset of scoliosis. Thus, both allow us to accurately track the patient’s morphology and atypical shape. The position of the morphological contours is indicated by reference marks that are closely associated with the skeleton. This helps to automatically adapt the garment to the evolution of the patient’s pathology over time. The process of creating the 3D garment was processed based on the 3D model of the thorax, which helps to easily determine the anthropometric points and the morphological curves. Using this data, the geometrical model of the garment could be created with 3D ease allowances. The 2D block pattern was then obtained by flattening the 3D patterns using flattening methods. Finally, various tests were performed considering the evolution of pathology to predict the future garment. These tests validate our geometrical model of the garment with 3D ease allowances by comparing the results with previous work.

10 November 2021 in RSC Advances
Verified
Journal Article
Open access
PDF file
YXYukang Xu
Yukang Xu
LWLei Wang
Lei Wang
GTGuangliang Tian
Guangliang Tian
YLYuanyuan Li
Yuanyuan Li
PWPing Wang
Ping Wang
XJXiangyu Jin
Xiangyu Jin
The waterjet impacting technology was introduced to split PTFE split-film fibers again to manufacture fine fibers for applications in the air purification field.