Özgür Gülsuna

Mr. Özgür Gülsuna

Middle East Technical University
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 October 2022 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
FTFurkan Tokgoz
Furkan Tokgoz
ÖGÖzgür Gülsuna
Özgür Gülsuna
FKFurkan Karakaya
Furkan Karakaya
GCGokhan Cakal
Gokhan Cakal
Ozan KeysanOzan Keysan
Ozan Keysan
PCB motors are a viable alternative to commercial electric motors as they are easy to mass-produce and have low manufacturing costs. Moreover, integrated motor drives have gained popularity thanks to their high power density and ease of installation. However, the mechanical and thermal aspects are challenging due to reduced volume. In this paper, a GaNFET switched integrated motor drive axial-flux permanent magnet synchronous machine with a printed circuit board (PCB) stator is designed. The machine is optimized using a multi-objective, non-dominated sorting genetic algorithm (NSGA-II). Two stator types are designed and manufactured to compare the effect of eddy losses. A method for measuring eddy current losses on PCB stators is proposed and used. A mechanical and thermal solution is proposed and tested. Integrated motor drive with sinusoidal pulsed width modulation (SPWM) is used to drive the motor up to 5000 RPM at a 1 MHz switching frequency. The overall system‘s efficiency is 82% at 0.36 N.m and 90% at 0.18 N.m torque. The system has an output power of 270 W of output power with 59 °C stator temperature that proved the effectiveness of the proposed passive cooling method.

16 May 2024 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
ÖGÖzgür Gülsuna
Özgür Gülsuna
FTFurkan Tokgoz
Furkan Tokgoz
FKFurkan Karakaya
Furkan Karakaya
Ozan KeysanOzan Keysan
Ozan Keysan
Printed circuit board (PCB) motors present a compelling alternative to commercial electric motors due to their cost-effective mass production. Furthermore, integrated motor drives have gained popularity thanks to their high power density and ease of installation. However, PCB motors face challenges due to their large effective air gap and fewer turns, resulting in low phase inductance. This article addresses these challenges by pairing the PCB motor with wide-bandgap devices and increasing the switching frequency to eliminate current ripple while reducing the size of filtering components, ultimately achieving a compact and efficient motor drive. The study explores various filtering options and decides upon for an L filter with line inductors on the motor phases. The losses of the system are analytically evaluated to a great extend leading to a selection of the switching frequency which is 1 MHz. Theoretical loss calculations are validated for both the electrical machine and inverter by means of calorimetric and electrical measurements. Finally, the integrated system is tested in motoring mode, operating at 5000 rpm and delivering 0.36 Nm of torque, resulting in an 82% efficiency. The article concludes that increasing the switching frequency is a feasible solution for low inductance motor drives.

16 May 2021 in Energies
Verified
Journal Article
Open access
PDF file
FKFurkan Karakaya
Furkan Karakaya
ÖGÖzgür Gülsuna
Özgür Gülsuna
Ozan KeysanOzan Keysan
Ozan Keysan
There are trade-offs for each power converter design which are mainly dictated by the switching component and passive component ratings. Recent power electronic devices such as Gallium Nitride (GaN) transistors can improve the application range of power converter topologies with lower conduction and switching losses. These new capabilities brought by the GaN High Electron Mobility Transistors (HEMTs) inevitably changes the feasible operation ranges of power converters. This paper investigates the feasibility of Buck and Boost based bi-directional DC/DC converter which utilizes Quasi-Square-Wave (QSW) Zero Voltage Switching (ZVS) on GaN HEMTs. The proposed converter applies a high-switching frequency at high output power to maximize the power density at the cost of high current ripple with high frequency of operation which requires a design strategy for the passive components. An inductor design methodology is performed to operate at 28 APP with a switching frequency of 450 kHz. In order to minimize the high ripple current stress on the output capacitors an interleaving is performed. Finally, the proposed bi-directional converter is operated at 5.4 kW with 5.24 kW/L or 85.9 W/in3 volumetric power density with air-forced cooling. The converter performance is verified for buck and boost modes and full load efficiencies are recorded as 97.7% and 98.7%, respectively.

3 October 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
EAEnes Ayaz
Enes Ayaz
OAOgün Altun
Ogün Altun
ÖGÖzgür Gülsuna
Özgür Gülsuna
Ozan KeysanOzan Keysan
Ozan Keysan
This study introduces a dual-mode wireless power transfer system for multistandard wireless charging products. The system allows two receivers to operate concurrently at narrowband and wideband frequencies using the proposed sinusoidal pulse width modulation (SPWM). Conventional SPWM does not provide independent control of switching and sideband harmonics, which are required for dual-mode excitation. We propose a new hybrid carrier and reference phase shift method to provide independent control of the reference, switching, and sideband harmonics. A prototype has been developed to validate power transfer at both narrowband (951 and 1190 kHz) and wideband (100 and 1190 kHz) frequency operations.