A cross-guide waveguide directional coupler (patent pending) with high directivity and broad bandwidth is proposed in this letter. It consists of two rectangular waveguides (called main waveguide and branch waveguide) crossing at a certain angle and sharing a common broad wall. High directivity is achieved by adding metal inserts in the branch waveguide in the coupling region near the crossed round-ended slots. For verification purpose, a sample coupler has been designed, manufactured and measured. The measured results show that the sample coupler has a directivity greater than 28 dB over the full waveguide bandwidth.
It is generally known that microstructure can considerably affect the tribological behavior of non-lubricated rubbing. However, there is still a lack of awareness about the effect of microstructure on oxidative wear. The present study focused on the effect of martensite volume fraction (MVF) on oxidative wear by using 25CD4 dual-phase steel. Dry friction tests were performed on a ball-on-flat tribometer with a normal load of 15 N and a mean sliding velocity of 0.013 m/s. Friction coefficient and wear rate increase with the increasing MVF. SEM observation and EDXS analyses of the wear scars showed that the oxidation increases with decreasing MVF. For lower MVF, the main wear mechanism is mild oxidative wear. For higher MVF, severe adhesion is predominant as a wear mechanism. The size of the debris decreases with decreasing MVF.
We study the geometric curvature and phase of the Rabi model. Under the rotating-wave approximation (RWA), we apply the gauge independent Berry curvature over a surface integral to calculate the Berry phase of the eigenstates for both single and two-qubit systems, which is found to be identical with the system of spin-1/2 particle in a magnetic field. We extend the idea to define a vacuum-induced geometric curvature when the system starts from an initial state with pure vacuum bosonic field. The induced geometric phase is related to the average photon number in a period which is possible to measure in the qubit-cavity system. We also calculate the geometric phase beyond the RWA and find an anomalous sudden change, which implies the breakdown of the adiabatic theorem and the Berry phases in an adiabatic cyclic evolution are ill-defined near the anti-crossing point in the spectrum.Comment: 18 pages, 5 figure
The focus of this study was the combined effects of sliding velocity (SV) and martensite volume fraction (MVF) on the tribological behavior of dual-phase (DP) steel. Dry frictional tests were realized on a ball-on-disk tribometer by unidirectional sliding at 0.1 m/s, 0.6 m/s, and 1 m/s. Considering the increase in SV, both the friction coefficient (COF) and wear rate decrease due to the increase in oxidative wear. At 0.1 m/s, the major wear mechanism is abrasive wear, accompanied by partial material flaking and less oxidation wear; at 0.6 m/s, the wear mechanism is in the transition between abrasive wear and oxidation wear; at 1 m/s, oxidation wear becomes the dominant wear mechanism. For the same SV, specimens with lower MVF exhibited lower wear compared to specimens with higher MVF; this phenomenon is especially evident at low SV. As the SV increases, the effect of MVF on the wear decreases, and the velocity becomes the dominant factor.
This paper presents a computational framework for designing and optimizing custom compression casts/braces. Different from the conventional cast/brace design, our framework generates custom casts/braces with fitness, lightweight, and good ventilation. The computational pipeline is an end-to-end solution, directly from customer to the manufacturer, which starts from a 3D scanned human model represented by mesh and ends with the 3D printed cast/brace. Our interactive tools allows users to define and edit the 3D curves on the mesh surface, and trim the mesh surface to form the cast/brace shape using the curves. These tools are efficient and simple to use, and also they enable designing the custom casts/braces fitting to the given human body. In order to reduce the weight and improve the ventilation, we adopt the topology optimization (TO) method to optimize the cast/brace design. We extend the existing three-dimensional (3D) TO method to the mesh surface by simplifying the optimization problem to a 2D problem. Therefore, the efficiency of the TO computation is improved significantly. After the optimized cast/brace design is obtained on the mesh surface, a solid model is generated by our design interface and then sent to a 3D printer for fabrication. Simulation results show that our method can better re-disturb the stresses compared with the conventional 3D TO.