Shojiro Ochiai

Prof. Dr. Shojiro Ochiai

orcid

Research Focus & Metrics

Academic Career Length

43Years (1984-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 June 2012 in Science and Technology of Advanced Materials
Verified
Journal Article
Open access
TITadanobu Inoue
Tadanobu Inoue
YKYuuji Kimura
Yuuji Kimura
SOShojiro Ochiai
Shojiro Ochiai
A 0.4C-2Si-1Cr-1Mo steel with an ultrafine elongated grain (UFEG) structure and an ultrafine equiaxed grain (UFG) structure was fabricated by multipass caliber rolling at 773 K and subsequent annealing at 973 K. A static three-point bending test was conducted at ambient temperature and at 77 K. The strength-toughness balance of the developed steels was markedly better than that of conventionally quenched and tempered steel with a martensitic structure. In particular, the static fracture toughness of the UFEG steel, having a yield strength of 1.86 GPa at ambient temperature, was improved by more than 40 times compared with conventional steel having a yield strength of 1.51 GPa. Furthermore, even at 77 K, the fracture toughness of the UFEG steel was about eight times higher than that of the conventional and UFG steels, despite the high strength of the UFEG steel (2.26 GPa). The UFG steel exhibited brittle fracture behavior at 77 K, as did the conventional steel, and no dimple structure was observed on the fracture surface. Therefore, it is difficult to improve the low-temperature toughness of the UFG steel by grain refinement only. The shape of crystal grains plays an important role in delamination toughening, as do their refinement and orientation.

30 June 2009 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
KOKozo Osamura
Kozo Osamura
SMS. Machiya
S. Machiya
HSH. Suzuki
H. Suzuki
SOShojiro Ochiai
Shojiro Ochiai
HAH. Adachi
H. Adachi
KSK. Sato
K. Sato
The DI (dynamically innovative)-BSCCO-Bi2223 tapes achieved high critical current as well as high modulus of elasticity. Further the reversible strain limit and the corresponding stress for critical current have been remarkably increased by means of lamination technique. During the course of development, their optimized architecture has been designed based on the principle of the rule of mixture for maximizing the force free strain exerted on the superconducting component. The reversible strain/stress limit (A rev/R rev) was defined as a strain, at which the critical current recovers to the level of 99% I co. Selecting several kinds of laminating materials and changing condition of the fabrication, the excellent Cu alloy-3ply tape with I co of 311 A/cm was realized of which A rev and R rev reached 0.42% and 300 MPa, respectively. Further during the theoretical analysis, the increase of reversible strain limit were made clear to be attributed to the increase of thermally induced residual strain as well as the compensation effect of laminated layers against a local fracture mode.

15 June 2008 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
SOShojiro Ochiai
Shojiro Ochiai
JSJ. K. Shin
J. K. Shin
SIShinichiro Iwamoto
Shinichiro Iwamoto
HOH. Okuda
H. Okuda
SOS. S. Oh
S. S. Oh
MSM. Sato
M. Sato
Mechanical and electromagnetic stresses are exerted on Bi2223∕Ag∕Ag alloy superconducting composite tapes during fabrication∕winding and operation, which cause reduction in critical current when the Bi2223 filaments are damaged. In the damage process, the thermally induced residual strain and fracture strain of the Bi2223 filaments play a dominant role. The aim of the present work was to propose a comprehensive method for estimation of these strain values and a quantitative description method of the relation of critical current to the applied bending∕tensile strain, and to examine the accuracy of the method in comparison with the experimental results. The residual strain of Bi2223 filaments in the composite tape was measured by the x-ray diffraction method. The measured residual strain value was used for analysis of the load-strain curve, from which the intrinsic fracture strain of filaments was estimated. The relation of critical current to applied bending∕tensile strain was predicted by the proposed calculation procedure, in which the estimated strain values were input. The predicted critical current-applied strain relation agreed well with the experimental results, suggesting that the present method is a useful tool for prediction∕description of tensile∕bending applied strain dependence of critical current of multifilamentary-type conductors.

1 August 2004 in Journal of Nuclear Materials
Verified
Journal Article
Closed access
SOShojiro Ochiai
Shojiro Ochiai
NMN Miyazaki
N Miyazaki
DDD Doko
D Doko
TNT Nagai
T Nagai
MNM Nakamura
M Nakamura
KOK Osamura
K Osamura

1 July 2005 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
SOShojiro Ochiai
Shojiro Ochiai
HOH. Okuda
H. Okuda
SIShinichiro Iwamoto
Shinichiro Iwamoto
TTT. Tomida
T. Tomida
TNT. Nakamura
T. Nakamura
MHM. Hojo
M. Hojo

1 January 2010 in MATERIALS TRANSACTIONS
Verified
Journal Article
Open access
PDF file
SOShojiro Ochiai
Shojiro Ochiai
SNSatoshi Nakano
Satoshi Nakano
YFYuya Fukazawa
Yuya Fukazawa
MAMohamed Shehata Aly
Mohamed Shehata Aly
HOHiroshi Okuda
Hiroshi Okuda
KHKeiichi Honma
Keiichi Honma
The change of Young’s modulus with increasing applied tensile strain in the open cell nickel and copper foams, fabricated by the slurry foaming process at Mitsubishi Materials Corporation, Japan, was investigated experimentally and analytically. Stress-strain curves were measured at room temperature, in which the loading-unloading-reloading process was performed on the sample at various applied strains. For measurement of the strain of the sample itself accurately, the non-contact extensometer was employed. The Young’s modulus values at various applied tensile strains were estimated from the slope of the elastic region in the stress-strain curve in the unloading process. It was revealed that two competitive factors affect on the Young’ modulus value. One is the irreversible morphology-change of cells arising from the plastic deformation of the metal as a results of which, the cells are elongated and struts are straight forwarded in the tensile direction. This factor acts to raise the Young’s modulus with increasing applied strain. Another factor is the failure of struts, which tends to reduce the Young’s modulus with increasing applied strain, especially beyond the strain where the struts are failed successively. Accordingly, due to the competition of the former and latter factors, the Young’s modulus increases, reaching maximum and then decreases with increasing applied strain in both of the foams. The increase in Young’s modulus with increasing applied strain due to the change of geometry of struts was confirmed by the experimental test of micro-samples composed of several struts and nodes and by the simulation based on the finite element analysis using a model micro-sample.