Muhammad Khan

Dr. Muhammad Khan

University of Warwick, Warwick UK

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2010 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
Muhammad KhanMuhammad Khan
Muhammad Khan
TMT. Mabrouki
T. Mabrouki
EVE. Vidal-Sallé
E. Vidal-Sallé
PBP. Boisse
P. Boisse

4 December 2009 in International Journal of Material Forming
Verified
Journal Article
Closed access
PDF file
Philippe BoissePhilippe Boisse
Philippe Boisse
YAYamina Aimène
Yamina Aimène
ADAbdelwaheb Dogui
Abdelwaheb Dogui
SDSamia Dridi
Samia Dridi
SGSébastien Gatouillat
Sébastien Gatouillat
EVEmmanuelle Vidal-Sallé
Emmanuelle Vidal-Sallé

8 November 2017 in Advanced Composite Materials
Verified
Journal Article
Closed access
Muhammad KhanMuhammad Khan
Muhammad Khan
ASAbdul Khadar Syed
Abdul Khadar Syed
HIHassan Ijaz
Hassan Ijaz
RSRaja Mazuir Raja Ahsan Shah
Raja Mazuir Raja Ahsan Shah
Cost and recyclability are among the primary factors on exploiting the engineering materials for their new applications. In this context, glass/pp-based sandwich panel has been studied experimentally and numerically with the aims of its potential applications in the automotive structures. The first part of this work presents the experimental results achieved for the load-carrying capacity of panels using three-point bend tests for its static flexural behaviour. Static behaviour is studied to compare the top-roller diameter effect on the flexural behaviour of the panels and shows a significant difference in the results. Impact behaviour of the panels is explored using three different types of impactor end-shapes that generate different levels of damage in the material with the same level of impact energy. The second part of this paper deals with the development of numerical models for the three-point bend and impact behaviour of the panels using a commercial finite element code of Abaqus. Strain energy-based homogenisation technique is employed to determine the equivalent orthotropic properties of complex circular honeycomb core material. The finite element models predict to a good level of the static and impact behaviour of the material when compared with the experiments.

9 June 2018 in Journal of Composite Materials
Verified
Journal Article
Closed access
CPCorentin Pasco
Corentin Pasco
Muhammad KhanMuhammad Khan
Muhammad Khan
JGJaipal Gupta
Jaipal Gupta
KKKenneth Kendall
Kenneth Kendall
A comprehensive novel investigation into the characterisation of interply friction behaviour of thermoset prepregs for high-volume manufacturing was conducted. High interply slipping rate and normal pressure typically used for high-volume manufacturing present challenges when preforming carbon fibre reinforced plastics. The study involved multiple reinforcement architectures (woven and unidirectional with the same rapid-cure resin system) which were characterised using a bespoke interply friction test rig used to simulate processing conditions representative to press forming and double diaphragm forming. Under prescribed conditions, woven and unidirectional prepregs exhibit significantly different frictional behaviour. Results demonstrated the unidirectional material obeys a hydrodynamic lubrication mode. For the woven material, a rate-dependent friction behaviour was found at low normal pressure. At higher normal pressure however, the woven material exhibited a friction behaviour similar to that of a dry reinforcement and significant tow displacement was observed. Post-characterisation analysis of test-specimens showed significant resin migration towards the outer edges of the plies, leaving a relatively resin-starved contact interface. The findings generate new knowledge on interply friction properties of thermoset prepreg for high-volume manufacturing applications, yet reveal a lack of understanding of the influence of tow tensions as well as the pre-impregnation level for a range of processing conditions.

1 November 2015 in Composite Structures
Verified
Journal Article
Closed access
Muhammad KhanMuhammad Khan
Muhammad Khan
NRNeil Reynolds
Neil Reynolds
GWG. Williams
G. Williams
KKK.N. Kendall
K.N. Kendall

1 April 2010 in International Journal of Material Forming
Verified
Journal Article
Closed access
PDF file
JSJ. Sargent
J. Sargent
JCJ. Chen
J. Chen
James SherwoodJames Sherwood
James Sherwood
JCJ. Cao
J. Cao
PBP. Boisse
P. Boisse
DJDavid JAUFFRES
David JAUFFRES