Device degradation induced by hot-carrier injection was repaired by electrical annealing using Joule heat through a built-in heater in a gate. The concentrated high temperature anneals the gate oxide locally and the degraded device parameters are recovered or further enhanced within a short time of 1 ms. Selecting a proper range of repair voltage is very important to maximize the annealing effects and minimize the extra damages caused by excessive high temperature. The repairing voltage is related to the resistance of the poly-Si gate according to the device scaling.
28 January 2020 in IEEE Transactions on Electron Devices
Gate dielectric damage caused by both internal and external stresses is becoming worse because of aggressive complementary metal-oxide-semiconductor (CMOS) scaling. However, conventional technologies for damage reduction using thermal annealing during fabrication have some limitations. As a result, there is a growing demand for technologies that will cure CMOS damage as a new paradigm for improving long-term reliability. This review paper reexamines self-recovery technologies, which are fully compatible with CMOS fabrication. Although self-heating has long been considered an unwanted operating side effect, it can also be favorably utilized to cure damage. Generated Joule heat arising from device operation can uniformly anneal the gate dielectric and effectively recover damage in various devices, such as conventional logic, memory, and aerospace CMOS devices, as well as thin-film transistors for displays.
6 March 2023 in IEEE Transactions on Electron Devices
Recently, nanosheet FETs (NS FETs) have been introduced as promising candidates for beyond 3-nm node technology. However, difficulties remain for mass production of the NS FETs. One of the concerns is increased OFF-state current ( ${I}_{ \mathrm{OFF}}$ ) due to leakage current from the substrate parasitic channel. Since the NS FET includes a 2-D parasitic FET on the bottom substrate, increased leakage current through the bottom is inevitable. The traditional methodology to suppress the leakage current from the parasitic channel is to use a punchthrough stopper (PTS). However, the PTS requires both ion implantation and an annealing process, which are detrimental to device yield. In this context, the trench gate (TG) NS FET is proposed as a new device architecture. The TG structure increases the effective gate length ( ${L}_{G\text {,EFF}}$ ) of the parasitic FET, reducing the leakage current through the bottom. Moreover, the fabrication process for the TG NS FET is fully compatible with conventional processes.
Mechanical stress is demonstrated in the fabrication process of nanosheet FETs. In particular, unwanted mechanical instability stemming from gravity during channel-release is covered in detail by aid of 3-D simulations. The simulation results show the physical weakness of suspended nanosheets and the impact of nanosheet thickness. Inner spacer engineering based on geometry and elastic property are suggested for better mechanical stability. The formation of wide contact area between inner spacer and nanosheet, as well as applying rigid spacer dielectric material, are preferred.
24 July 2020 in IEEE Transactions on Electron Devices
High-pressure (HP) deuterium (D₂) annealing was applied to a gate-all-around (GAA) MOSFET to improve device reliability and memory performance. The structure had gate dielectrics of oxide-nitride-oxide (ONO), which completely straddled vertically stacked multiple silicon nanowires (Si-NWs) with n⁺ poly-Si gates. The HP D₂ annealing was effective for the vertically stacked GAA MOSFET as it was for a conventional planar MOSFET. In addition, the resistance of the n⁺ poly-Si gate was also reduced after the HP D₂ annealing. This is attributed to the passivation of defects among adjacent poly-Si grains by the HP D₂. The reduced gate resistance (RG) is advantageous for decreasing RC delay. Direct characterizations of dc I-V and analyses of ac low-frequency noise (LFN) supported the abovementioned behaviors.
Self-heating effects (SHEs) in three-dimensional (3D) V-NAND flash memory are investigated using simulations. First, temperature increase is estimated during the read operation, and a hot spot region along the bit-line is identified. Then, a novel bilayered macaroni filler was proposed to relieve the SHEs. A highly thermally conductive layer is plugged into the macaroni oxide filler as a heat sink. The heat dissipation efficiency is improved by up to 21 % in the proposed structure. As a result, the reliability issues induced by SHEs can be avoided in V-NAND flash.