Barge-type platforms with moonpools are a promising type of foundation for floating offshore wind turbines due to their good seakeeping performance. In this paper, the mean wave drift force on a barge-type vertical-axis floating wind turbine with multiple moonpools was investigated through physical model testing and numerical calculations using WAMIT. The focus was on the characteristics of mean drift load and its optimization potential. The present numerical results indicated that the application of moonpools was useful in reducing horizontal mean drift force at specific frequencies, and the reason was ascribed to the significant radiation effect of the resonant water oscillations in moonpools. The observed reduction effect on mean drift force was shown to be dependent on the viscous damping of moonpool resonance. The experimental results showed that the maximum response of the mean sway drift force was reduced by the gyroscopic effect of rotations of the vertical-axis wind turbine, and this reduction effect became stronger as the rotating speed of the wind turbine increased, but was weakened as wave amplitude increased. The comparisons between experimental data and potential flow predictions indicated that viscous effects should be taken into account to reasonably estimate the mean wave drift forces on barge-type floating wind turbines.
17 October 2011 in Journal of Offshore Mechanics and Arctic Engineering
This paper describes hydroelastic motion and effect of motion reduction of large floating structures in head sea conditions, supported by aircushion. Motion reduction effects, appearing due to the presence of aircushions, have been confirmed through theoretical calculations with the zero-draft assumption. Three-dimensional prediction method has been developed for evaluating draft influence of division walls of aircushions. Using three-dimensional theoretical calculations, authors have investigated whether hydroelastic motion reduction is possible or not. Next, aircushion type bodies were supported by multiple aircushions, which are smaller in size than the wavelengths. Green’s function method within the linear potential theory was applied for prediction of hydrodynamic forces and wave excitations, in which the effect of free water surface between aircushions was considered. Hydroelastic responses were estimated not only in terms of elastic motion, but also in terms of vertical bending moment. The results confirmed the existence of response reduction, especially noticeable for the vertical bending moment in a wide wavelength range and in the whole structure area.
1 January 1997 in Journal of the Society of Naval Architects of Japan
A target offshore structure in this study is an aircushion supported very large floating structure. The aircushion type VLFSs behave elastically in water waves. Corresponding aircushions are very large or relatively small size. The VLFSs considered in this study are supported by a large aircushion, two aircushions, or several module aircushions. The zero-draft theory is applied to the prediction of the hydrodynamic forces. The zero-draft theory is based on the pressure distribution method. The elastic deflection predicted by the zero-draft method is compared with that by another three-dimensional method in order to confirm the validity of it. In addition, the steady wave drifting forces on VLFSs with the aircushion are shown and their characteristics are examined. Then, the momentum theory is applied to the prediction. In the final section, effects of aircushion division to the elastic deflection and the wave drifting force are investigated. From the results, it is confirmed that the elastic deflection is can be reduced in the specification relation between the wavelength and the length of a module aircushion. In addition, it is possible to ajust the aircushion setting in order to simultaneously reduce the elastic deflection and the steady wave drifting force of the aircushion type VLFS on the case.
24 February 2016 in Journal of Offshore Mechanics and Arctic Engineering
This paper describes a method to improve the performance of primary conversion of wave power takeoff. The wave energy converter (WEC) used here was of oscillating water column (OWC) type. This method for improvement has been already proposed in past research and its usefulness has been confirmed. It involves projecting walls (PWs) being attached to the front of the inlet–outlet of the OWC. The prediction method of hydrodynamic behaviors for the OWC type WEC with PWs installed is explained in this paper. The boundary element method with the Green's function is applied, and influence of air pressure and free surface within every air-chamber was directly taken into consideration in the prediction method based on linear potential theory. Validity of the prediction method was proved by comparing the results with the results of model experiments. Series calculations are performed with the prediction method. Behaviors of air pressure, water elevation, and the efficiency of primary conversion of wave power were investigated. From the calculations, length of the PWs was shown to affect the efficiency of primary conversion. It was possible to equip the PWs so as to enable improvements in oblique waves to beam sea conditions as well as in the head sea conditions. This paper examined not only the PWs but also the application and effects of the end walls (EWs) with the slit. The EWs were very useful to improve the efficiency.
25 February 2013 in Journal of Offshore Mechanics and Arctic Engineering
In recent years, a number of floating facilities for the utilization of ocean space, such as a marine disaster prevention base, floating restaurant, or floating container terminal, are planned, and some of them are actually built. Most of these facilities are of the pontoon-type floating structure, and the mooring system is basically a mooring dolphin. In the design of such facilities, it is important that the prediction of the motions of a pontoon-type floating body, supported by a mooring dolphin, in a tsunami is obtained. The objective of the present research is to develop a simulation system to obtain such predictions. In the present simulation system developed here, the three-dimensional (3D) MPS method (moving particle semi-implicit method) is used, and a solitary wave and borelike wave are applied to represent the incoming tsunami wave. The present paper is a report of the first stage of the research, and the heaving motion of the floating body acted upon by the tsunami is paid special attention, and we also report on the results of the study of the detaching of the floating body from the mooring dolphin.