We present a photo-excited switchable broadband reflective linear polarization conversion metasurface for terahertz waves. The unit-cell structure of the switchable polarization conversion metasurface is composed of metallic disk and split-ring resonator (together named as DSRR) integrated with semiconductor photoconductive silicon (Si) placed over the continuous films. The electric response of the photoconductive Si filled in the gap of the DSRR can be tunable through a pump beam with different optical power. The simulation results indicate that the polarization conversion ratio (PCR) of the compound metasurface without pump beam is greater than 80% in the frequency range of 0.65-1.58 THz, and the PCR is up to 99% at resonances frequencies of 0.69 THz, 1.01 THz and 1.42 THz, respectively. The numerical simulation results are in good agreement with the theoretical predictions based on the interference theory. Furthermore, the broadband PCR can be tunable continuously with the changes of Si conductivity by adjusting the pump optical power. Moreover, the surface current distributions of the unit-cell structure with different Si conductivity at the resonance frequency are discussed to illustrate its physics mechanism. Thus, our design can find potential applications in many areas, such as remote sensors, reflector antennas, and radiometers in terahertz region.
The world is entering a new era with ubiquitous connectivity among billions of humans and machines, i.e., the sixth-generation (6G) massive Internet of Things (IoT). Radar and communication need to be integrated into this system to achieve target detection and massive connectivity. In this work, we first develop a shape-adaptive antenna array composed of multiple subarrays spaced at regular intervals. The shape-adaptive antenna array uses flexible material that enables changes in the physical structure to achieve adaptive gain. Subsequently, we investigate the micromovement of IoT targets, such as the micro-motion characteristics and micro-Doppler effects of rotary-wing drones. The simulation results demonstrate the effectiveness and efficiency of the proposed schemes for detecting unmanned aerial vehicles (UAVs) in an IoT scenario.
14 July 2019 in Wireless Communications and Mobile Computing
Unmanned aerial vehicles (UAVs) have broad application potential for the Internet of Things (IoT) due to their small size, low cost, and flexible control. At present, the main positioning method for UAVs is the use of GPS. However, GPS positioning may be affected by stronger electromagnetic signals from spoofing attacks. In this study, a radar-assisted positioning method based on 5G millimeter waves is proposed. In 5G end-to-end network slices, the rotors of UAVs can be detected and identified by deploying 5G millimeter wave radar. High-resolution range profile (HRRP) is used to obtain the UAV location in the detection zone. Micro-Doppler characteristics are used to identify the UAVs and the cepstrum method is used to extract the number and speed information of the UAV rotor. The sinusoidal frequency modulation (SFM) parameter optimization method is used to separate multiple UAVs. The proposed method provides information on the number of UAVs, the position of the UAV, the number of rotors, and the rotation speed of each rotor. The simulation results show that the proposed radar detection method is well suited for UAV detection and identification and provides a valid GPS-independent method for UAV tracking.
Microwave plasma jets based on a coaxial transmission line resonator show outstanding advantages such as portability, lower power consumption, and low-temperature operation. In this manuscript, the most important of the five gaseous reactive oxygen and nitrogen species (RONS) densities including OH, O, O3, NO, and NO2 densities are measured synchronously, while the plasma jet is treating a biological tissue under different discharge parameters (gas composition, gas flow, skin humidity, and output power). It has been found that the gas composition and the output power are two key factors to regulate the dose of RONS concentrations. For the OH concentration, water vapor in the gas flow plays an important role. By changing the microwave power and the gas composition, the OH concentration changes from 0.4 × 1014 cm−3 to 5.54 × 1014 cm−3. O is mostly affected by the O2 percentage in Ar, and 1% percentage is the optimal value. O3 is proportional to the O2 percentage in Ar, and 2% O2 can get a maximum O3 density of 6.9 × 1016 cm−3. NO is in the range of 2 × 1013 cm−3 to 5.4 × 1014 cm−3, and NO2 is in the range of 5.5 × 1014 cm−3 to 5 × 1015 cm−3. The increase in the humidity of the skin has a positive effect on the concentration of OH, O3, and NO while a negative effect on the O and NO2 concentration. For the normal skin with a humidity of 40%, the concentrations of the long lifetime species like O3 and NO2 are almost 101–2 times those of the other reactive species. This research provides parameter setting guidance for different RONS requirements.
7 August 2015 in IEEE Antennas and Wireless Propagation Letters
This letter presents three measurement approaches for three-dimensional (3-D) inverse synthetic aperture radar (ISAR) imaging of rotating objects on a pylon in compact antenna test range. The proposed measurement approaches are based on the backprojection algorithm and the concept of interferometric ISAR. Point spread functions (PSFs) are simulated to assess the performance of the proposed approaches. Simulation results show an improvement of up to 87% reduction in measurement time while maintaining an 8-dB peak sidelobe ratio (PSLR).
Today’s power systems are developing from traditional multi-sensor systems to ubiquitous power Internet of Things systems. The environmental backscatter technology makes communication equipment get rid of the dependence on power supply, is more energy-efficient, and effectively extends the communication distance, which is very suitable for power Internet of Things scenarios. Tag antenna is an important part of environmental backscattering, but it has problems such as low reliability and insufficient reading distance in the traditional power Internet of Things. In view of the above problems, this paper designs a double-antenna structure tag antenna, which adopts omnidirectional receiving and directional transmitting methods to achieve the purpose of comprehensive signal coverage for the power Internet of Things application scenarios. It has the characteristics of obvious gain, small side lobe, and strong anti-interference.