Esús Esarte

Dr. Esús Esarte

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 July 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
EEEsús Esarte
Esús Esarte
Jesús M. BlancoJesús M. Blanco
Jesús M. Blanco
ABangela bernardini
angela bernardini
RSRamon Sancibrian
Ramon Sancibrian
The primary wick in a loop heat pipe device is a key component that is central to the operation of the device. Both high permeability and capillary pumping capacity, two properties highly dependent on wick structure, are strongly desirable for a satisfactory thermal performance. In this paper, selective laser melting (SLM), a three-dimensional (3D) printing technology, is used to create a primary wick for an 80 W heat transfer application. The permeability and capillarity values of this wick, experimentally measured, are compared with those built with the most widely used technologies nowadays, such as powder sintering and meshes. In this study, the SLM scaffold is shown to satisfy the minimum values required by the application in terms of capillarity and permeability: 0.031 mm/s and 4 × 10−12 m2, respectively. Our comparative study revealed that the wick produced with the SLM technology presented higher values of permeability, by two orders of magnitude, and slightly higher capillary figures than those corresponding to powder sintering for such application. However, it had capillary values well below those of a stainless-steel mesh. The hydraulic behavior of the SLM wick was better than that of the sintered copper powder, because it not only met the above-mentioned specifications, but it also improved its performance.

18 August 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
GAGorka Argandoña
Gorka Argandoña
MAMaite Aresti
Maite Aresti
Jesús M. BlancoJesús M. Blanco
Jesús M. Blanco
EMEsteban Muel
Esteban Muel
EEEsús Esarte
Esús Esarte
In most steelmaking processes, huge amounts of waste heat at high temperature (700–800 °C) are thrown into the environment without any use. An alternative use for this waste heat is electricity generation through thermoelectric generators. However, these high temperatures, as well as their fluctuations over time, affect not only the conversion rate of the thermoelectric generator but also its useful lifetime. The incorporation of a latent thermal energy storage (TES) system could be a solution; nevertheless, the thermal stability and corrosive effect of the (PCM) phase change material are key aspects for the thermal storage system definition, in terms of durability. In this work, developed in the framework of the European project “PowGETEG” (RFSR-CT-2015-00028, funded by the Research Fund for Coal and Steel), a high-temperature analysis (700–800 °C) of the Li2CO3 thermal properties, thermal stability and corrosive effect on the AISI 304 and AISI 310 stainless steels is carried out. The results show that the eutectic salt Li2CO3 exhibits high thermal stability with neither change in its thermal properties nor material degradation. This work shows that lithium carbonate Li2CO3 and AISI 310 make a very good combination for the definition of a thermal storage system able to protect a high-temperature thermoelectric converter from temperature variations, making it more reliable.

26 March 2021
Verified
Book Chapter
Open access
PDF file
EEEsús Esarte
Esús Esarte
RRRoger R Riehl
Roger R Riehl
Mancin SimoneMancin Simone
Mancin Simone
Jesús M. BlancoJesús M. Blanco
Jesús M. Blanco
MAMaite Aresti
Maite Aresti
JEJuncal Estella
Juncal Estella
Nanofluids are defined as heat transfer fluids with enhanced heat transfer properties by the addition of nanoparticles. Nanofluid’s stability, nanoparticles’ type and their chemical compatibility with the base fluid are essential not only to increase the nanofluid’s thermophysical properties but also to ensure a long-lasting and thermal efficient use of the equipment in which it is used. Some of these aspects are discussed in this chapter. Likewise, the improvement in terms of the heat transfer capacity (thermal resistance) that the use of nanofluids has on the heat pipes-thermosyphons is shown. On the other hand, the improvement in energy efficiency that nanofluid causes in a vapor compression system is also presented.