Regarding crashworthiness, many published works have focused on designing thin-walled structures for frontal collisions compared to side-impact collisions. This paper presents an experimental investigation and finite element modelling of a carbon-reinforced thin-walled top-hat section subjected to quasi-static and dynamic transverse bending loads at different impact speeds. The top-hat sections and their closure assembly plates were made of MTM44 prepreg carbon. The specimens were manufactured by vacuum bagging. Dynamic work was performed to validate the results obtained from the finite element analysis (FEA). The predicted results are in good agreement with the experimental results. The study also showed that the peak load and energy absorption owing to dynamic loading were higher than those under static loading. In the four-point bend analysis, the stacking sequence affected the energy absorption capabilities by 15–30%. In addition, the distance between the indenters in the four-point analysis also affected the energy absorption by 10% for the same impact condition, where a larger distance promoted higher energy absorption. The study also demonstrated that a top-hat shaped thin-walled structure is suitable for deep intrusion beams in vehicle doors for side-impact crashworthiness applications.
29 February 2024 in Journal of Engineering and Technological Sciences
The performance of carbon fiber reinforced polymer (CFRP) composite materials under quasi-static and high strain rate loading can be predicted with a high level of accuracy using the non-linear finite element analysis (FEA) method. Experimental validation tests under uniaxial tensile loading have shown a good correlation with FEA predictions for thermoset polymer composites, using commercially available epoxy resin MTM710 with carbon fiber reinforcement and for comparative tests on DP600 steel and aluminum alloys (AC170 and 5754 series). The physical and numerical results comparison of composite, aluminum, and high-strength steel indicates that the composite may be used as an alternative to aluminum and high-strength steel since the composite was shown to have almost the same strength as steel and higher strength than aluminum with the advantage of being lightweight and possessing similar mechanical behavior under quasi-static conditions. The results demonstrated that the strain rate range used did not significantly affect the strength of the composite materials. The selection of materials can be optimized reliably by FEA based on mechanical properties, cost, and weight. This will significantly reduce the new product introduction timescale, which is essential for the wider use of polymer composites for structural applications, especially in the automotive industry.
Vehicle crashworthiness is an important aspect to consider when designing a vehicle to ensure the safety of the occupants. Besides this, vehicles are also designed to reduce weight for better fuel economics. One possible approach to reducing weight without compromising vehicle safety is by looking at new designs and usage of composite materials, along with the usage of computational models to reduce time and cost. Hence, this paper displays the experimental results of a carbon fiber reinforced closed top-hat section subjected to both quasi-static and dynamic crushing loading. The results were used to validate the computational model developed in the study. The specimens were made of carbon composite prepregs MTM-44 sheets stacked at the alternative orientation of ±45° and 0°/90°, where 0° direction coincides with the axis of the member. The samples were prepared by using a mold and carbon prepregs under vacuum bagging followed by curing in an autoclave. Trigger initiation was applied to ensure the specimens demonstrated a stable crushing mode of failure during the test. Experimental investigations were carried out under the ambient conditions with different loading conditions, and different kinetic energy ranges (2, 3 and 6 kJ). Experimental data was used to validate the finite element analysis (FEA). The maximum errors obtained between experimental and FEA for mean load, mean energy absorption, and crushing displacement were 13%, 13% and 7%, respectively. The numerically obtained results were in strong agreement with the experimental data and showed that they were able to predict the failure of the specimens. The work also showed the novelty of using such structures for energy absorption applications.
5 February 2025 in Journal of Engineering and Technological Sciences
The study aims to investigate the effect of numerical analysis on a bitubular circular tube subjected to dynamic loading. To compare its performance, a circular monotube specimen with a perimeter of 300 mm, a thickness of 2 mm, and a length of 350 mm was used as a reference. The bitubular circular tubes consist of two tubes, an inner and an outer. The outer tube's perimeter was initially set at 350mm with a wall thickness of 1 mm, while the inner tube had a perimeter of 250 mm and a thickness of 1 mm. The outer perimeter was gradually decreased by 10 mm, while the inner tube's perimeter was simultaneously increased by 10 mm for each configuration. This process was repeated until reaching perimeter lengths of 305 mm and 295 mm for the outer and inner tubes, respectively. The outer tube's length remained fixed at 350 mm, the same as the reference tube's length. The inner tube's length was initially kept identical to the outer tube while changing the tube's perimeter, aiming to maintain the same mass insofar as was possible compared to the reference tube. The inner tube of each configuration was then shortened by 10 mm until reaching a length of 300 mm. Six specimens were selected as the best performers based on the lowest load and highest crush force efficiency (CFE) criteria using the complex proportional assessment (COPRAS) technique. The results revealed that the best design was the bitubular configuration with an outer tube perimeter of 340 mm, an inner tube perimeter of 260 mm, and an inner tube length of 320 mm. This configuration achieved a 44% reduction in peak force, a 19% increase in crash force efficiency (CFE), and a 3.7% decrease in mass compared to the reference monotube. These findings indicate that the chosen bitubular configuration achieves a desirable balance of reduced peak force and improved crash force efficiency, making it a promising design for energy absorption and occupant protection during collisions.