School of Information Technology and Electrical Engineering, The University of Queensland, Sir Fred Schonell Drive, St Lucia, Brisbane, QLD 4072, Australia
Prof. Neil Bergmann
School of Information Technology and Electrical Engineering, The University of Queensland, Sir Fred Schonell Drive, St Lucia, Brisbane, QLD 4072, Australia
Often the Internet of Things (IoT) is considered as a single problem domain, with proposed solutions intended to be applied across a wide range of applications. However, the privacy and security needs of critical engineering infrastructure or sensitive commercial operations are very different to the needs of a domestic Smart Home environment. Additionally, the financial and human resources available to implement security and privacy vary greatly between application domains. In domestic environments, human issues may be as important as technical issues. After surveying existing solutions for enhancing IoT security, the paper identifies key future requirements for trusted Smart Home systems. A gateway architecture is selected as the most appropriate for resource-constrained devices, and for high system availability. Two key technologies to assist system auto-management are identified. Firstly, support for system auto-configuration will enhance system security. Secondly, the automatic update of system software and firmware is needed to maintain ongoing secure system operation.
11 June 2012 in IEEE Transactions on Instrumentation and Measurement
This paper proposes a novel industrial wireless sensor network (IWSN) for industrial machine condition monitoring and fault diagnosis. In this paper, the induction motor is taken as an example of monitored industrial equipment due to its wide use in industrial processes. Motor stator current and vibration signals are measured for further processing and analysis. On-sensor node feature extraction and on-sensor fault diagnosis using neural networks are then investigated to address the tension between the higher system requirements of IWSNs and the resource-constrained characteristics of sensor nodes. A two-step classifier fusion approach using Dempster-Shafer theory is also explored to increase diagnosis result quality. Four motor operating conditions-normal without load, normal with load, loose feet, and mass imbalance-are monitored to evaluate the proposed system. Experimental results show that, compared with raw data transmission, on-sensor fault diagnosis could reduce payload transmission data by 99%, decrease node energy consumption by 97%, and prolong node lifetime from 106 to 150 h, an increase of 43%. The final fault diagnosis results using the proposed classifier fusion approach give a result certainty of at least 97.5%. To leverage the advantages of on-sensor fault diagnosis, another system operating mode is explored, which only transmits the fault diagnosis result when a fault happens or at a fixed interval. For this mode, the node lifetime reaches 73 days if sensor nodes transmit diagnosis results once per hour.
With the rapid development of sensor networks and embedded computing technologies, miniaturized wearable healthcare monitoring devices have become practically feasible. For many of these devices, accelerometer-based user authentication systems by gait analysis are becoming a hot research topic. However, a major bottleneck of such system is it requires continuous sampling of accelerometer, which reduces battery life of wearable sensors. In this paper, we present KEH-Gait, which advocates use of output voltage signal from kinetic energy harvester (KEH) as the source for gait recognition. KEH-Gait is motivated by the prospect of significant power saving by not having to sample the accelerometer at all. Indeed, our measurements show that, compared to conventional accelerometer-based syste, KEH-Gait can reduce energy consumption by 82.15%. The feasibility of KEH-Gait is based on the fact that human gait has distinctive movement patterns for different individuals, which leaves distinctive patterns for KEH as well. We evaluate KEH-Gait using two different types of KEH hardware on a data set of 20 subjects. Our experiments demonstrate that, although KEH-Gait yields slightly lower accuracy than accelerometer-based gait detection when single step is used, the accuracy problem can be overcome by the proposed Probability-based Multi-Step Sparse Representation Classification (PMSSRC). Moreover, the security analysis shows that the EER of KEH-Gait against an active spoofing attacker is 11:2% and 14:1% using two different types of KEH hardware respectively.
Ubiquity of wearable and implantable devices sparks a new set of mobile computing applications that leverage the prolific information of sensors. For many of these applications, to ensure the security of communication between legitimate devices is a crucial problem. In this paper, we design Walkie-Talkie, a shared secret key generation scheme that allows two legitimate devices to establish a common cryptographic key by exploiting users' walking characteristics (gait). The intuition is that the sensors on different locations of the same body experience similar accelerometer signal when the user is walking. However, the accelerometer also captures motion signal produced by other body parts (e.g., swinging arms). We address this issue by employing Blind Source Separation (BSS) technique to extract the informative signal produced by the unique gait pattern. Our experimental results show that the keys generated by two independent devices on the same body are able to achieve up to 100% bit agreement rate. To demonstrate the feasibility, we implement the proposed key generation scheme on modern smartphones. The evaluation results show that the proposed scheme can run in real-time on modern mobile devices and incurs low system overhead.
There is an increasing need for environmental measurement systems to further science and thereby lead to improved policies for sustainable management. Marine environments are particularly hostile and extremely difficult for deploying sensitive measurement systems. As a consequence the need for data is greatest in marine environments, particularly in the developing economies/regions. Expense is typically the most significant limiting factor in the number of measurement systems that can be deployed, although technical complexity and the consequent high level of technical skill required for deployment and servicing runs a close second. This paper describes the Smart Environmental Monitoring and Analysis Technologies (SEMAT) project and the present development of the SEMAT technology. SEMAT is a “smart” wireless sensor network that uses a commodity-based approach for selecting technologies most appropriate to the scientifically driven marine research and monitoring domain/field. This approach allows for significantly cheaper environmental observation systems that cover a larger geographical area and can therefore collect more representative data. We describe SEMAT’s goals, which include: (1) The ability to adapt and evolve; (2) Underwater wireless communications; (3) Short-range wireless power transmission; (4) Plug and play components; (5) Minimal deployment expertise; (6) Near real-time analysis tools; and (7) Intelligent sensors. This paper illustrates how the capacity of the system has been improved over three iterations towards realising these goals. The result is an inexpensive and flexible system that is ideal for short-term deployments in shallow coastal and other aquatic environments.