Electrically conductive yarns (ECYs) are gaining increasing applications in woven textile materials, especially in woven sensors suitable for incorporation into clothing. In this paper, the effect of the yarn count of ECYs woven into fabric on values of electrical resistance is analyzed. We also observe how the direction of action of elongation force, considering the position of the woven ECY, effects the change in the electrical resistance of the electrically conductive fabric. The measurements were performed on nine different samples of fabric in a plain weave, into which were woven ECYs with three different yarn counts and three different directions. Relationship curves between values of elongation forces and elongation to break, as well as relationship curves between values of electrical resistance of fabrics with ECYs and elongation, were experimentally obtained. An analytical mathematical model was also established, and analysis was conducted, which determined the models of function of connection between force and elongation, and between electrical resistance and elongation. The connection between the measurement results and the mathematical model was confirmed. The connection between the mathematical model and the experimental results enables the design of ECY properties in woven materials, especially textile force and elongation sensors.

The welding of foils, textiles, and textile composites made of thermoplastic polymer materials using machines with an ultrasonic rotary sonotrode is a high-tech welding technique. Many authors have dealt with only a few parameters in earlier papers, mainly mentioning the speed, i.e., the welding time, and the power of the ultrasonic generator. In this paper, the acoustic model of ultrasonic welding is defined. Based on the model, a group of 44 different parameters important for ultrasonic welding of polymer materials has been summarised, namely 12 parameters of the polymer material, 11 general acoustic and electroacoustic parameters, and 21 technical parameters depending on the ultrasonic machine. Based on this, a comprehensive mathematical derivation was carried out, linking parameter groups with other findings from acoustics, thermodynamics of polymers, and technical and technological parameters of welding polymer materials. The most important parameters are the power of the ultrasonic generator and the welding time, which in practice are adjusted to produce a solid weld. The method of measuring the amplitude of the sonotrode using a photonic sensor is presented in this paper. For 42 groups of welds done at various welding speeds and ultrasonic generator powers, the breaking forces of ultrasonic welds were measured. There are illustrations of power dependence and breaking forces. The accuracy of the mathematical model was confirmed by comparison with the calculation results based on the findings of these measurements.

In recent years, more and more researchers have been focused on electrically conductive textiles that generate heat or transmit electrical signals and energy to embedded electrical components. In this paper, the dissipation of heat due to the flow of electric current at given voltages is investigated, and at the same time it is determined how this heat affects the change in the electrical resistance of the electrically conductive yarn in the immediate surroundings. Three fabric samples were woven in a plain weave with three types of different electrically conductive yarns. Three electrically conductive yarns are woven in parallel in the weft direction and separated from each other by one polyester (PES) yarn due to electrical insulaton. Conductive yarns are electrically connected so that the outer yarns are used for heating by the flow of electric current at a certain constant voltage, and the central yarn is used only to measure changes in electrical resistance. When electrothermally conductive fabrics are subjected to certain voltages over time, experimental results have shown that resistance values increase over a short period of time and then gradually decrease, while the temperature gradually increases and stabilizes over time. Based on the analysis of the obtained results of the ratio between the values of applied voltage and temperature to the electrically conductive yarns, the value of thermal dissipation in conductive yarns can be calculated in advance depending on the applied voltage. Furthermore, the obtained results can be further used in applications where conductive yarns are used as heaters for realistic prediction of the obtained heat.

This paper describes methods for evaluating the thermal properties of textile materials, clothing composites, and clothing using an integrated measurement system that includes a hot plate, a multi-purpose differential conductometer, a thermal manikin, a temperature gradient measurement device, and a device for measuring the physiological parameters of the human body during the exact evaluation of garment thermal comfort. In practice, measurements were taken on four types of materials widely used in the production of conventional and protective clothing. The measurements were carried out using a hot plate and a multi-purpose differential conductometer, determining the thermal resistance of the material both in its uncompressed form and when a force was applied that was ten times greater than that needed to determine its thickness. Using a hot plate and a multi-purpose differential conductometer, thermal resistances of textile materials were assessed at different levels of material compression. On hot plates, both conduction and convection had an impact on thermal resistance, but in the multi-purpose differential conductometer, only conduction did. Moreover, a reduction in thermal resistance was observed as a result of compressing textile materials.

The thermal properties of most clothing products are still not designed according to engineering science due to the lack of simple and acceptable measuring equipment and methods; the type of thermal insulation material, the number of layers of clothing and their thickness are thus chosen empirically. The novelty of this study was the development of a new measuring device and method for simultaneous measurements in the determination of the thermal resistance in one or more textile material layers, such as in multilayer composite clothing. Temperature gradients of textile material layers are presented, as well as the theoretical principles of operation and practical results. Four materials for the production of protective jackets were selected, from which different combinations of composite clothing were constructed and the thermal parameters were measured with a new method and a new device, both individually for the built-in materials and for the composites. Subsequently, five test jackets with the same arrangement of textile material layers as the previously tested composites were produced, and measurements of important thermal parameters were recorded with a thermal mannequin. The determined temperature gradients and measurement results are presented, and based on these it was determined that the total thermal resistance was not equal to the algebraic sum of the resistances of the individual textile material layers in the horizontal position; it was, however, higher, increasing from 30% to 94% due to small air layers caused by crimping and protruding fibres of yarn in the textile fabrics. The same textile material layers built into clothing in the vertical position allowed the formation of significantly wider air layers that increased the thermal resistance by between 2.5 and 9 times.

The paper presents a new method for determining the machine-hand welding times of synthetic polymer materials using ultrasonic welding machines with rotary sonotrode. The method is based on the claims and observations of W. Möller intended for the clothing industry in the 1990s, according to which there is a spontaneous drop in sewing speed when strongly curved seams are joined, which is due to the possibility of human reactions. The method for determining machine-hand sewing times of curved seams was well accepted in garment production processes. It is used to standardize production time. Using ultrasonic welding machines with rotary sonotrode, the problem of determining the time of ultrasonic joining of curved seams on clothing or technical textiles remained unsolved. That is why is completely new and original model was created, which combines eight technical parameters of ultrasonic welds, eight technological parameters of the production process and seven ergonomic parameters depending on the psychophysical conditions of the workers. The systematic development of the mathematical relationship of all 23 parameters mentioned and the corresponding mathematical expressions for determining and calculating these parameters are presented. These results were also verified by experimental measurements, which show a favourable correlation between the calculated and measured machine hand times. The relationships between the recommended welding speeds, the critical radii of curvature and the number of reactions required according to Möller and the new model are also presented. An analysis of the success in the application of Möller’s and the new model was also performed.