Power generation technologies based on water movement and evaporation use water, which covers more than 70% of the Earth’s surface and can also generate power from moisture in the air. Studies are conducted to diversify materials to increase power generation performance and validate energy generation mechanisms. In this study, a water-based generator was fabricated by coating cellulose acetate with carbon black. To optimize the generator, Fourier-transform infrared spectroscopy, specific surface area, zeta potential, particle size, and electrical performance analyses were conducted. The developed generator is a cylindrical generator with a diameter of 7.5 mm and length of 20 mm, which can generate a voltage of 0.15 V and current of 82 μA. Additionally, we analyzed the power generation performance using three factors (physical properties, cation effect, and evaporation environment) and proposed an energy generation mechanism. Furthermore, we developed an eco-friendly and low-cost generator using natural fibers with a simple manufacturing process. The proposed generator can contribute to the identification of energy generation mechanisms and is expected to be used as an alternative energy source in the future.

Water evaporation-driven energy harvesting is an emerging mechanism for contributing to green energy production with low cost. Herein, we developed polyacrylonitrile (PAN) nanofiber-based evaporation-driven electricity generators (PEEGs) to confirm the feasibility of utilizing electrospun PAN nanofiber mats in an evaporation-driven energy harvesting system. However, PAN nanofiber mats require a support substrate to enhance its durability and stability when it is applied to an evaporation-driven energy generator, which could have additional effects on generation performance. Accordingly, various support substrates, including fiberglass, copper, stainless mesh, and fabric screen, were applied to PEEGs and examined to understand their potential impacts on electrical generation outputs. As a result, the PAN nanofiber mats were successfully converted to a hydrophilic material for an evaporation-driven generator by dip-coating them in nanocarbon black (NCB) solution. Furthermore, specific electrokinetic performance trends were investigated and the peak electricity outputs of V_oc were recorded to be 150.8, 6.5, 2.4, and 215.9 mV, and I_sc outputs were recorded to be 143.8, 60.5, 103.8, and 121.4 μA, from PEEGs with fiberglass, copper, stainless mesh, and fabric screen substrates, respectively. Therefore, the implications of this study would provide further perspectives on the developing evaporation-induced electricity devices based on nanofiber materials.

In this study, we investigate the influence of Sc microalloying on the microstructure of the Al5083 alloy. Trace amounts of Sc addition drastically improve the mechanical properties of the Al5083 alloy from 216 MPa to 233 MPa. Macroscopically, the addition of Sc significantly reduces the grain size of Al by approximately 50%. Additionally, a microstructural investigation reveals that the Sc microalloying element induces fine Al₃Sc nanoprecipitates in the Al matrix. The formation of Al₃Sc nanoprecipitates results in a pinning effect on the dislocations, leading to accumulated dislocations. Compared to a Sc-free Al5083 alloy specimen, the number density of dislocations in the Sc-added Al5083 alloy significantly increases after hot rolling, enhancing the tensile properties. We reveal that the improved mechanical properties of Al5083 with Sc microalloying originate from the grain refinement and the formation of fine Al₃Sc nanoprecipitates.

The widespread use of single-use face masks during the recent epidemic has led to significant environmental challenges due to waste pollution. This study explores an innovative approach to address this issue by repurposing discarded face masks for hydrovoltaic energy harvesting. By coating the face masks with carbon black (CB) to enhance their hydrophilic properties, we developed mask-based hydrovoltaic power generators (MHPGs). These MHPGs were evaluated for their hydrovoltaic performance, revealing that different mask configurations and sizes affect their efficiency. The study found that MHPGs with smaller, more structured areas exhibited better energy output, with maximum open-circuit voltages (V_OC) reaching up to 0.39 V and short-circuit currents (I_SC) up to 65.6 μA. The integration of CB improved water absorption and transport, enhancing the hydrovoltaic performance. More specifically, MHPG-1 to MHPG-4, which represented different sizes and features, presented mean V_OC values of 0.32, 0.17, 0.19 and 0.05 V, as well as mean I_SC values of 16.57, 15.59, 47.43 and 3.02 μA, respectively. The findings highlight the feasibility of utilizing discarded masks in energy harvesting systems, offering both environmental benefits and a novel method for renewable energy generation. Therefore, this work provides a new paradigm for waste-to-energy (WTE) technologies and inspires further research into the use of unconventional waste materials for energy production.